rommon 60 set IP_ADDRESS 10.16.131.115
usage: set
rommon 61 "IP_ADDRESS=10.16.1.2"
rommon 62 "IP_SUBNET_MASK=255.255.255.0"
rommon 63 "DEFAULT_GATEWAY=10.16.1.1"
rommon 64 "TFTP_SERVER=10.16.1.4"
rommon 65 "TFTP_FILE=c2600-i-mz.121-5.T8"
rommon 66 tftpdnld
IP_ADDRESS: 10.16.1.2
IP_SUBNET_MASK: 255.255.255.0
DEFAULT_GATEWAY: 10.16.1.1
TFTP_SERVER: 10.16.1.4
TFTP_FILE: c2600-i-mz.121-5.T8
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash will be lost!
Do you wish to continue? y/n: [n]: y
Receiving c2600-i-mz.121-5.T8 from 10.16.1.4 !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!
File reception completed.
Copying file c2600-i-mz.121-5.T8 to flash.
Erasing flash at 0x607c0000
program flash location 0x604e0000
rommon 67
rommon 67
rommon 67
rommon 67 boot
program load complete, entry point: 0x80008000, size: 0x4e02f0
Self decompressing the image : #################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
### [OK]
Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
000091 0X00092280 C2600 single Ethernet
0X000F34A8 public buffer pools
0X00211000 public particle pools
TOTAL: 0X00396728
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 4Mb.
Using 12 percent iomem. [4Mb/32Mb]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.1(5)T8, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Mon 07-May-01 17:57 by ccai
Image text-base: 0x80008088, data-base: 0x80972320
cisco 2610 (MPC860) processor (revision 0x203) with 28672K/4096K bytes of memory
.
Processor board ID JAD05090M7A (447016375)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Press RETURN to get started!
00:00:12: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
00:00:12: %LINK-3-UPDOWN: Interface Serial0/0, changed state to up
00:00:12: %LINK-3-UPDOWN: Interface Serial0/1, changed state to down
00:00:13: %SYS-5-CONFIG_I: Configured from memory by console
00:00:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed s
tate to up
00:00:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed sta
te to down
00:00:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed sta
te to down
00:00:14: %LINK-5-CHANGED: Interface Serial0/1, changed state to administrativel
y down
00:00:15: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.1(5)T8, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Mon 07-May-01 17:57 by ccai
Cisco2610-003
Cisco2610-003en
