分享
 
 
 

Guide to Cisco Frame Relay Traffic Shaping

王朝other·作者佚名  2008-05-31
窄屏简体版  字體: |||超大  

FRTS uses a mechanism called a Token BUCket.

The Token Bucket regulates the amount of data that can be sent from the Frame Relay interface during a specific time period, 1/8th of a second by default.

Data can be sent out the Frame Relay interface only if there are enough free tokens in the token bucket.

If there are enough tokens, the data is sent and the appropriate amount of tokens are removed from the Token Bucket.

If there are not enough tokens, the router will buffer the data until the Token Bucket has enough tokens to send the data and then remove the appropriate amount of tokens.

Before proceeding please note that there are two basic types of FRTS implementations.

(1) FRTS with only local concern to the Frame Network

(2) FRTS configuration with remote concern for other routers on the network. For example, if you need to throttle bandwidth down on your T1 so that you so not overwhelm the remote router which is running at just 128k.

Frame Relay Terms and How They Apply to Cisco FRTS Implementations:

AR (Access Rate)

This is the depth of the token bucket. This is the physical circuit speed

to your frame provider.

Local Example: If you have agreed to purchase a 128k circuit to your Frame Provider, your AR is 128k.

Remote Example: If you have 128k physical circuit and you intend to lower the rate of data transmission to a remote site which only has a 64k AR, you would then set this to 64k.

Implementation: When configuring Cisco FRTS using the data from the Local Example above, this will be entered using "cir".

frame-relay cir 128000.

CIR (Committed Information Rate)

This is the average amount of data that you and your service provider have agreed that you will send per second. This is normally lower than your AR.

Local Example: Your Frame Relay Service Provider has stated that your CIR = 64k. You now have a 128k physical circuit to your provider with a CIR of 64k.

Remote Example: If you have 64k CIR to your provider and you need to throttle bandwidth down so you don't overwhelm your you remote router which has a 32k CIR, you would set this to 32K CIR.

Implementation: When configuring Cisco FRTS using the data from the Local Example above, this will be entered using "mincir"

frame-relay mincir 64000

Bc - (Committed Burst)

This is the amount of data that can be sent during a time interval. That time interval is identified by "Tc", which by default is 1/8th of a second.

Bc = AR/8

Local Example: In order to send traffic to meet your 128k AR, Bc = 16000bps.

Remote Example: This would be set to 1/8th of the remote routers AR.

Implementation: When configuring Cisco FRTS using the data from the Local Example above, this will be entered using "bc"

frame relay bc 16000

Be - (Excess Burst)

This is the difference between CIR and AR. Configure Be only if CIR is less than AR.

Local Example: If your CIR is 64k and your access rate is 128k, then your Be is 64k.

Remote Example: The difference between cir and mincir. If cir = 128000 and mincir = 64000, then be = 64000

Implementation: When configuring Cisco FRTS using the data from the Local Example, this will be entered using "be".

frame-relay be 64000

Tc (Time Interval)

Time interval is the time measurement that works with Bc to control the amount of data that is allowed to be sent to the token bucket. The router calculates this value based on AR and Bc values that you enter. Tc = Bc/AR.

By default on a Cisco router, it is 0.125 (125ms). If Bc/AR. is greater than or equal to 125msec, it uses the internal Tc value of 125msec. If Bc/AR is less than 125 ms, it uses the Tc calculated from that equation. Why does this matter? A Tc should be adjusted to 10ms if you are running Voice across the Frame Relay circuit.

Before proceding, please once again note the difference in terminology:

FRAME RELAY TERMINOLOGY CISCO TERMINOLOGY USING FRTS

AR - ACCESS RATE = CIR – COMMITED INFORMATION RATE

CIR - COMMINITED INFORMATION RATE = MINCIR - MINIMUM COMMITED INFORMATION RATE

Examples:

Single Site

If you were to traffic shape to your Frame Relay provider, you would do the following. Let's say your provider has given you the following:

"Welcome to Global.Net WAN Services. Your 512k circuit has been installed. Per our agreement, you have a 384k CIR to our Frame Network. Thank you for using Global.Net."

Here is how you would configure your router:

int s0

frame-relay traffic-shaping

int s0.1

Frame-relay class hub

map-class frame-relay hub

frame-relay adaptive-shaping becn

Frame-relay cir 512000

Frame-relay mincir 384000

Frame-relay be 128000

Frame-relay bc 64000

Hub and Spoke

Note:

As soon as we begin to configure FRTS to adapt for other routers on our network, in most cases our Cisco map-class settings now begin to reflect the requirements put upon us by the remote router.

Scenario 1

You have a hub site with T1 port access and 128k cir from your provider. You are communicating to a remote site, which only has 64k port access and 32k cir to the same Frame network. You'll want to throttle the hub site down enough so that it does not overwhelm the remote site with traffic.

Hub Site

int s0

frame-relay traffic-shaping

int s0.1

frame-relay class hub

map-class frame-relay hub

frame-relay adaptive-shaping becn

frame-relay cir 64000

frame-relay mincir 32000

frame-relay be 32000

frame-relay bc 8000

Scenario 2

You have a hub site with 512 port access 256k cir from provider communicating with 2 spoke remote sites which also have 512k port access 256k cir from provider. You'll want to throttle the spoke sites down enough so that they do not overwhelm the hub router.

Spoke Sites

int s0

frame-relay traffic-shaping

int s0.1

frame-relay class spoke

map-class frame-relay spoke

frame-relay adaptive-shaping becn

frame-relay cir 256000

frame-relay mincir 128000

frame-relay be 128000

frame-relay bc 32000

256k above.

With CIR we have to share bandwidth for the hub with the other remote router, so our CIR is now set to 256000 which is = of the hub routers port speed.

BC should always be 1/8th of your CIR setting in the Cisco map class unless you are running voice.

 
 
 
免责声明:本文为网络用户发布,其观点仅代表作者个人观点,与本站无关,本站仅提供信息存储服务。文中陈述内容未经本站证实,其真实性、完整性、及时性本站不作任何保证或承诺,请读者仅作参考,并请自行核实相关内容。
2023年上半年GDP全球前十五强
 百态   2023-10-24
美众议院议长启动对拜登的弹劾调查
 百态   2023-09-13
上海、济南、武汉等多地出现不明坠落物
 探索   2023-09-06
印度或要将国名改为“巴拉特”
 百态   2023-09-06
男子为女友送行,买票不登机被捕
 百态   2023-08-20
手机地震预警功能怎么开?
 干货   2023-08-06
女子4年卖2套房花700多万做美容:不但没变美脸,面部还出现变形
 百态   2023-08-04
住户一楼被水淹 还冲来8头猪
 百态   2023-07-31
女子体内爬出大量瓜子状活虫
 百态   2023-07-25
地球连续35年收到神秘规律性信号,网友:不要回答!
 探索   2023-07-21
全球镓价格本周大涨27%
 探索   2023-07-09
钱都流向了那些不缺钱的人,苦都留给了能吃苦的人
 探索   2023-07-02
倩女手游刀客魅者强控制(强混乱强眩晕强睡眠)和对应控制抗性的关系
 百态   2020-08-20
美国5月9日最新疫情:美国确诊人数突破131万
 百态   2020-05-09
荷兰政府宣布将集体辞职
 干货   2020-04-30
倩女幽魂手游师徒任务情义春秋猜成语答案逍遥观:鹏程万里
 干货   2019-11-12
倩女幽魂手游师徒任务情义春秋猜成语答案神机营:射石饮羽
 干货   2019-11-12
倩女幽魂手游师徒任务情义春秋猜成语答案昆仑山:拔刀相助
 干货   2019-11-12
倩女幽魂手游师徒任务情义春秋猜成语答案天工阁:鬼斧神工
 干货   2019-11-12
倩女幽魂手游师徒任务情义春秋猜成语答案丝路古道:单枪匹马
 干货   2019-11-12
倩女幽魂手游师徒任务情义春秋猜成语答案镇郊荒野:与虎谋皮
 干货   2019-11-12
倩女幽魂手游师徒任务情义春秋猜成语答案镇郊荒野:李代桃僵
 干货   2019-11-12
倩女幽魂手游师徒任务情义春秋猜成语答案镇郊荒野:指鹿为马
 干货   2019-11-12
倩女幽魂手游师徒任务情义春秋猜成语答案金陵:小鸟依人
 干货   2019-11-12
倩女幽魂手游师徒任务情义春秋猜成语答案金陵:千金买邻
 干货   2019-11-12
 
推荐阅读
 
 
 
>>返回首頁<<
 
靜靜地坐在廢墟上,四周的荒凉一望無際,忽然覺得,淒涼也很美
© 2005- 王朝網路 版權所有