RFC70 - Note on Padding

王朝other·作者佚名  2008-05-31
窄屏简体版  字體: |||超大  

Network Working Group S. Crocker

Request for Comments #70 UCLA

15 October 70

A Note on Padding

The padding on a message is a string of the form 10*. For Hosts with

Word lengths 16, 32, 48, etc., bits long, this string is necessarily in

the last word received from the Imp. For Hosts with word lengths which

are not a multiple of 16 (but which are at least 16 bits long), the 1

bit will be in either the last word or the next to last word. Of

course if the 1 bit is in the next to last word, the last word is all

zero.

An unpleasant coding task is discovering the bit position of the 1 bit

within its word. One obvious technique is to repeatedly test the

low-order bit, shifting the word right one bit position if the

low-order bit is zero. The following techniques are more pleasant.

Isolating the Low-Order Bit

Let W be a non-zero word, where the word length is n. Then W is of the

form

x....x10....0

\__ __/\__ __/

V V

n-k-1 k

where 0<=k<n

and the x's are arbitrary bits.

Assuming two's complement arithmetic,

W-1 = x....x01....1

_ _

-W = x....x10....0

_ _ _

W = x....x01....1

By using AND, OR and exclusive OR with various pairs of these

quantities, useful new forms are oBTained.

For example,

W AND W-1 xx...x00....0

\__ __/\__ __/

V V

n-k-1 k

thus removing the low-order 1 bit;

also W AND -W = 0....010....0

__ __/__ __/

V V

n-k-1 k

thus isolating the low-order bit.

Below, we will focus solely on this last result; however, in a

particular application it may be advantageous to use a variation.

Determining the Position of an Isolated Bit

The two obvious techniques for finding the bit position of an isolated

bit are to shift repetitively with tests, as above, and to use floating

normalization hardware. On the PDP-10, in particular, the JFFO

instruction is made to order*. On machines with hexadecimal

normalization, e.g. IBM 360's and XDS Sigma 7's, the normalization

hardware may not be very convenient. A different approach uses

division and table look-up.

k

A word with a single bit on has an unsigned integer value of 2 for

k

0<=k<n. If we choose a p such that mod(2 ,p) is distinct for each

0<=k<n, we can make a table of length p which gives the correspondence

k

between mod(2 ,p) and k. The remainder of this paper is concerned with

the selection of an appropriate divisor p for each word length n.

*Some of the CDC machines have a "population count" instruction which

k

gives the number of bits in a word. Note the 2 -1 has exactly k bits

on.

Example

Let n = 8 and p = 11

Then

0

mod(2, 11) = 1

1

mod(2, 11) = 2

2

mod(2, 11) = 4

3

mod(2, 11) = 8

4

mod(2, 11) = 5

5

mod(2, 11) = 10

6

mod(2, 11) = 9

7

mod(2, 11) = 7

This yields a table of the form

remainder bit position

0 --

1 0

2 1

3 --

4 2

5 4

6 --

7 7

8 3

9 6

10 5

Good Divisors

The divisor p should be as small as possible in order to minimize the

length of the table. Since the divisor must generate n distinct

remainders, the divisor will certainly need to be at least n. A

remainder of zero, however, can occur only if the divisor is a power of

j

2. If the divisor is a small power of 2, say 2 for j < n-1, it will

not generate n distinct remainders; if the divisor is a larger power of

n-1 n

2, the correspondence table is either 2 or 2 in length. We can

thus rule out zero as a remainder value, so the divisor must be at

least one more than the word length. This bound is in fact achieved

for some word lengths.

Let R(p) be the number of distinct remainders p generates when divided

into successively higher powers of 2. The distinct remainders all occur

for the R(p) lowest powers of 2. Only odd p are interesting and the

following table gives R(p) for odd p between 1 and 21.

p R(p) p R(p)

1 1 13 12

3 2 15 4

5 4 17 8

7 3 19 18

9 6 21 6

11 10

This table shows that 7, 15, 17 and 21 are useless divisors because

there are smaller divisors which generate a larger number of distinct

remainders. If we limit our attention to p such that p > p' =>

R(p) > R(p'), we obtain the following table of useful divisors for

p < 100.

p R(p) p R(p)

1 1 29 28

3 2 37 36

5 4 53 52

9 6 59 58

11 10 61 60

13 12 67 66

19 18 83 82

25 20

Notice that 9 and 25 are useful divisors even though they generate only

6 and 20 remainders, respectively.

Determination of R(p)

If p is odd, the remainders

0

mod(2 ,p)

1

mod(2 ,p)

.

.

.

t

will be between 1 and p-1 inclusive. At some power of 2, say 2 , there

k t

will be a repeated remainder, so that for some k < t, 2 = 2 mod p.

t+1 k+1

Since 2 = 2 mod p

t+2 k+2

and 2 = 2 mod p

.

.

.

etc.

0 t-1

all of the distinct remainders occur for 2 ...2 . Therefore, R(p)=t.

Next we show that

R(p)

2 = 1 mod p

R(p) k

We already know that 2 = 2 mod p

for some 0<=k<R(p). Let j=R(p)-k so 0<j<=R(p). Then

k+j k

2 = 2 mod p

j k k

or 2 *2 = 2 mod p

j k

or (2 -1)*2 = 0 mod p

k j

Now p does not divide 2 because p is odd, so p must divide 2 -1. Thus

j

2 -1 = 0 mod p

j

2 = 1 mod p

Since j is greater than 0 by hypothesis and since ther is no k other

than 0 less than R(p) such that

k 0

2 = 2 mod p,

R(p)

we must have j=R(p), or 2 = 1 mod p.

k

We have thus shown that for odd p, the remainders mod(2 ,p) are unique

for k = 0, 1,..., R(p)-1 and then repeat exactly, beginning with

R(p)

2 = 1 mod p.

We now consider even p. Let

q

p = p'*2 ,

k k k

where p' is odd. For k<q, mod(2 ,p) is clearly just 2 because 2 <p.

For k>=q,

k q k-q

mod(2 ,p) = 2 *mod(2 ,p').

From this we can see that the sequence of remainders will have an

q-1

initial segment of 1, 2, ...2 of length q, and repeating segments of

length R(p'). Therefore, R(p) = q+R(p'). Since we normally eXPect

R(p) ~ p,

even p generally will not be useful.

I don't know of a direct way of choosing a p for a given n, but the

previous table was generated from the following Fortran program run

under the SEX system at UCLA.

0

CALL IASSGN('OC ',56)

1 FORMAT(I3,I5)

M=0

DO 100 K=1,100,2

K=1

L=0

20 L=L+1

N=MOD(2*N,K)

IF(N.GT.1) GO TO 20

IF(L.LE.M) GO TO 100

M=L

WRITE(56,1)K,L

100 CONTINUE

STOP

END

Fortran program to computer useful divisors

In the program, K takes on trial values of p, N takes on the values of

the successive remainders, L counts up to R(p), and M remembers the

previous largest R(p). Execution is quite speedy.

Results from Number Theory

The quantity referred to above as R(p) is usually written Ord 2 and is

p

read "the order of 2 mod p". The maximum value of Ord 2 is given by

p

Euler's phi-function, sometimes called the totient. The totient of a

positive integer p is the number of integers less than p which are

relatively prime to p. The totient is easy to compute from a

representation of p as a product of primes:

n n n

Let p = p 1 * p 2 ... p k

1 2 k

where the p are distinct primes. Then

i

k -1 k -1 k -1

phi(p) = (p - 1) * p 1 * (p - 1) * p 2 ... (p - 1) * p k

1 1 2 2 k k

If p is prime, the totient of p is simply

phi(p) = p-1.

If p is not prime, the totient is smaller.

If a is relatively prime to p, then Euler's generalization of Fermat's

theorem states

phi(m)

a = 1 mod p.

It is this theorem which places an upper bound Ord 2, because Ord 2 is

p p

the smallest value such that

Ord 2

2 p = 1 mod p

Moreover it is always true that phi(p) is divisible by Ord 2.

p

Acknowledgements

Bob Kahn read an early draft and made many comments which improved the

exposition. Alex Hurwitz assured me that a search technique is

necessary to compute R(p), and supplied the names for the quantities

and theorems I uncovered.

[ This RFCwas put into machine readable form for entry ]

[ into the online RFCarchives by Guillaume Lahaye and ]

[ John Hewes 6/97 ]

 
 
 
免责声明:本文为网络用户发布,其观点仅代表作者个人观点,与本站无关,本站仅提供信息存储服务。文中陈述内容未经本站证实,其真实性、完整性、及时性本站不作任何保证或承诺,请读者仅作参考,并请自行核实相关内容。
 
 
© 2005- 王朝網路 版權所有 導航