Network Working Group B. Carpenter
Request for Comments: 3056 K. Moore
Category: Standards Track February 2001
Connection of IPv6 Domains via IPv4 Clouds
Status of this Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2001). All Rights Reserved.
Abstract
This memo specifies an optional interim mechanism for IPv6 sites to
communicate with each other over the IPv4 network without eXPlicit
tunnel setup, and for them to communicate with native IPv6 domains
via relay routers. Effectively it treats the wide area IPv4 network
as a unicast point-to-point link layer. The mechanism is intended as
a start-up transition tool used during the period of co-existence of
IPv4 and IPv6. It is not intended as a permanent solution.
The document defines a method for assigning an interim unique IPv6
address prefix to any site that currently has at least one globally
unique IPv4 address, and specifies an encapsulation mechanism for
transmitting IPv6 packets using sUCh a prefix over the global IPv4
network.
The motivation for this method is to allow isolated IPv6 domains or
hosts, attached to an IPv4 network which has no native IPv6 support,
to communicate with other such IPv6 domains or hosts with minimal
manual configuration, before they can oBTain natuve IPv6
connectivity. It incidentally provides an interim globally unique
IPv6 address prefix to any site with at least one globally unique
IPv4 address, even if combined with an IPv4 Network Address
Translator (NAT).
Table of Contents
1. Introduction................................................. 2
1.1. Terminology................................................ 4
2. IPv6 Prefix Allocation....................................... 5
2.1 Address Selection........................................... 6
3. Encapsulation in IPv4........................................ 6
3.1. Link-Local Address and NUD................................. 7
4. Maximum Transmission Unit.................................... 7
5. Unicast scenarios, scaling, and transition to normal prefixes 8
5.1 Simple scenario - all sites work the same................... 8
5.2 Mixed scenario with relay to native IPv6................... 9
5.2.1 Variant scenario with ISP relay.......................... 12
5.2.2 Summary of relay router configuration.................... 12
5.2.2.1. BGP4+ not used........................................ 12
5.2.2.2. BGP4+ used............................................ 12
5.2.2.3. Relay router scaling.................................. 13
5.2.3 Unwilling to relay....................................... 13
5.3 Sending and decapsulation rules............................ 13
5.4 Variant scenario with tunnel to IPv6 space................. 14
5.5 Fragmented Scenarios....................................... 14
5.6 Multihoming................................................ 16
5.7 Transition Considerations.................................. 16
5.8 Coexistence with firewall, NAT or RSIP..................... 16
5.9 Usage within Intranets..................................... 17
5.10 Summary of impact on routing.............................. 18
5.11. Routing loop prevention.................................. 18
6. Multicast and Anycast....................................... 19
7. ICMP messages............................................... 19
8. IANA Considerations......................................... 19
9. Security Considerations..................................... 19
Acknowledgements............................................... 20
References..................................................... 20
Authors' Addresses............................................. 22
Intellectual Property.......................................... 22
Full Copyright Statement....................................... 23
1. Introduction
This memo specifies an optional interim mechanism for IPv6 sites to
communicate with each other over the IPv4 network without explicit
tunnel setup, and for them to communicate with native IPv6 domains
via relay routers. Effectively it treats the wide area IPv4 network
as a unicast point-to-point link layer. The mechanism is intended as
a start-up transition tool used during the period of co-existence of
IPv4 and IPv6. It is not intended as a permanent solution.
The document defines a method for assigning an interim unique IPv6
address prefix to any site that currently has at least one globally
unique IPv4 address, and specifies an encapsulation mechanism for
transmitting IPv6 packets using such a prefix over the global IPv4
network. It also describes scenarios for using such prefixes during
the co-existence phase of IPv4 to IPv6 transition. Note that these
scenarios are only part of the total picture of transition to IPv6.
Also note that this is considered to be an interim solution and that
sites should migrate when possible to native IPv6 prefixes and native
IPv6 connectivity. This will be possible as soon as the site's ISP
offers native IPv6 connectivity.
The basic mechanism described in the present document, which applies
to sites rather than individual hosts, will scale indefinitely by
limiting the number of sites served by a given relay router (see
Section 5.2). It will introduce no new entries in the IPv4 routing
table, and exactly one new entry in the native IPv6 routing table
(see Section 5.10).
Although the mechanism is specified for an IPv6 site, it can equally
be applied to an individual IPv6 host or very small site, as long as
it has at least one globally unique IPv4 address. However, the
latter case raises serious scaling issues which are the subject of
further study [SCALE].
The motivation for this method is to allow isolated IPv6 sites or
hosts, attached to a wide area network which has no native IPv6
support, to communicate with other such IPv6 domains or hosts with
minimal manual configuration.
IPv6 sites or hosts connected using this method do not require IPv4-
compatible IPv6 addresses [MECH] or configured tunnels. In this way
IPv6 gains considerable independence of the underlying wide area
network and can step over many hops of IPv4 subnets. The abbreviated
name of this mechanism is 6to4 (not to be confused with [6OVER4]).
The 6to4 mechanism is typically implemented almost entirely in border
routers, without specific host modifications except a suggested
address selection default. Only a modest amount of router
configuration is required.
Sections 2 to 4 of this document specify the 6to4 scheme technically.
Section 5 discusses some, but not all, usage scenarios, including
routing ASPects, for 6to4 sites. Scenarios for isolated 6to4 hosts
are not discussed in this document. Sections 6 to 9 discuss other
general considerations.
The key Words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
1.1. Terminology
The terminology of [IPV6] applies to this document.
6to4 pseudo-interface:
6to4 encapsulation of IPv6 packets inside IPv4 packets occurs
at a point that is logically equivalent to an IPv6 interface,
with the link layer being the IPv4 unicast network. This point
is referred to as a pseudo-interface. Some implementors may
treat it exactly like any other interface and others may treat
it like a tunnel end-point.
6to4 prefix:
an IPv6 prefix constructed according to the rule in Section 2
below.
6to4 address: an IPv6 address constructed using a 6to4 prefix.
Native IPv6 address: an IPv6 address constructed using another type
of prefix than 6to4.
6to4 router (or 6to4 border router):
an IPv6 router supporting a 6to4 pseudo-interface. It is
normally the border router between an IPv6 site and a wide-area
IPv4 network.
6to4 host:
an IPv6 host which happens to have at least one 6to4 address.
In all other respects it is a standard IPv6 host.
Note: an IPv6 node may in some cases use a 6to4 address for a
configured tunnel. Such a node may function as an IPv6 host using a
6to4 address on its configured tunnel interface, and it may also
serve as a IPv6 router for other hosts via a 6to4 pseudo-interface,
but these are distinct functions.
6to4 site:
a site running IPv6 internally using 6to4 addresses, therefore
containing at least one 6to4 host and at least one 6to4 router.
Relay router:
a 6to4 router configured to support transit routing between
6to4 addresses and native IPv6 addresses.
6to4 exterior routing domain:
a routing domain interconnecting a set of 6to4 routers and
relay routers. It is distinct from an IPv6 site's interior
routing domain, and distinct from all native IPv6 exterior
routing domains.
2. IPv6 Prefix Allocation
Suppose that a subscriber site has at least one valid, globally
unique 32-bit IPv4 address, referred to in this document as V4ADDR.
This address MUST be duly allocated to the site by an address
registry (possibly via a service provider) and it MUST NOT be a
private address [RFC1918].
The IANA has permanently assigned one 13-bit IPv6 Top Level
Aggregator (TLA) identifier under the IPv6 Format Prefix 001 [AARCH,
AGGR] for the 6to4 scheme.Its numeric value is 0x0002, i.e., it is
2002::/16 when expressed as an IPv6 address prefix.
The subscriber site is then deemed to have the following IPv6 address
prefix, without any further assignment procedures being necessary:
Prefix length: 48 bits
Format prefix: 001
TLA value: 0x0002
NLA value: V4ADDR
This is illustrated as follows:
3 13 32 16 64 bits
+---+------+-----------+--------+--------------------------------+
FP TLA V4ADDR SLA ID Interface ID
0010x0002
+---+------+-----------+--------+--------------------------------+
Thus, this prefix has exactly the same format as normal /48 prefixes
assigned according to [AGGR]. It can be abbreviated as
2002:V4ADDR::/48. Within the subscriber site it can be used exactly
like any other valid IPv6 prefix, e.g., for automated address
assignment and discovery according to the normal mechanisms such as
[CONF, DISC], for native IPv6 routing, or for the "6over4" mechanism
[6OVER4].
Note that if the IPv4 address is assigned dynamically, the
corresponding IPv6 prefix will also be dynamic in nature, with the
same lifetime.
2.1 Address Selection
To ensure the correct operation of 6to4 in complex topologies, source
and destination address selection must be appropriately implemented.
If the source IPv6 host sending a packet has at least one 2002::
address assigned to it, and if the set of IPv6 addresses returned by
the DNS for the destination host contains at least one 2002::
address, then the source host must make an appropriate choice of the
source and destination addresses to be used. The mechanisms for
address selection in general are under study at the time of writing
[SELECT]. Subject to those general mechanisms, the principle that
will normally allow correct operation of 6to4 is this:
If one host has only a 6to4 address, and the other one has both a
6to4 and a native IPv6 address, then the 6to4 address should be used
for both.
If both hosts have a 6to4 address and a native IPv6 address, then
either the 6to4 address should be used for both, or the native IPv6
address should be used for both. The choice should be configurable.
The default configuration should be native IPv6 for both.
3. Encapsulation in IPv4
IPv6 packets from a 6to4 site are encapsulated in IPv4 packets when
they leave the site via its external IPv4 connection. Note that the
IPv4 interface that is carrying the 6to4 traffic is notionally
equivalent to an IPv6 interface, and is referred to below as a
pseudo-interface, although this phrase is not intended to define an
implementation technique. V4ADDR MUST be configured on the IPv4
interface.
IPv6 packets are transmitted in IPv4 packets [RFC791] with an IPv4
protocol type of 41, the same as has been assigned [MECH] for IPv6
packets that are tunneled inside of IPv4 frames. The IPv4 header
contains the Destination and Source IPv4 addresses. One or both of
these will be identical to the V4ADDR field of an IPv6 prefix formed
as specified above (see section 5 for more details). The IPv4 packet
body contains the IPv6 header and payload.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Version IHL Type of Service Total Length
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Identification Flags Fragment Offset
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Time to Live Protocol 41 Header Checksum
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Source Address
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Destination Address
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Options Padding
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
IPv6 header and payload ... /
+-------+-------+-------+-------+-------+------+------+
The IPv4 Time to Live will be set as normal [RFC791], as will the
encapsulated IPv6 hop limit [IPv6]. Other considerations are as
described in Section 4.1.2 of [MECH].
3.1. Link-Local Address and NUD
The link-local address of a 6to4 pseudo-interface performing 6to4
encapsulation would, if needed, be formed as described in Section 3.7
of [MECH]. However, no scenario is known in which such an address
would be useful, since a peer 6to4 gateway cannot determine the
appropriate link-layer (IPv4) address to send to.
Neighbor Unreachability Detection (NUD) is handled as described in
Section 3.8 of [MECH].
4. Maximum Transmission Unit
MTU size considerations are as described for tunnels in [MECH].
If the IPv6 MTU size proves to be too large for some intermediate
IPv4 subnet, IPv4 fragmentation will ensue. While undesirable, this
is not necessarily disastrous, unless the fragments are delivered to
different IPv4 destinations due to some form of IPv4 anycast. The
IPv4 "do not fragment" bit SHOULD NOT be set in the encapsulating
IPv4 header.
5. Unicast scenarios, scaling, and transition to normal prefixes
5.1 Simple scenario - all sites work the same
The simplest deployment scenario for 6to4 is to use it between a
number of sites, each of which has at least one connection to a
shared IPv4 Internet. This could be the global Internet, or it could
be a corporate IP network. In the case of the global Internet, there
is no requirement that the sites all connect to the same Internet
service provider. The only requirement is that any of the sites is
able to send IPv4 packets with protocol type 41 to any of the others.
By definition, each site has an IPv6 prefix in the format defined in
Section 2. It will therefore create DNS records for these addresses.
For example, site A which owns IPv4 address 192.1.2.3 will create DNS
records with the IPv6 prefix {FP=001,TLA=0x0002,NLA=192.1.2.3}/48
(i.e., 2002:c001:0203::/48). Site B which owns address 9.254.253.252
will create DNS records with the IPv6 prefix
{FP=001,TLA=0x0002,NLA=9.254.253.252}/48 (i.e., 2002:09fe:fdfc::/48).
When an IPv6 host on site B queries the DNS entry for a host on site
A, or otherwise obtains its address, it obtains an address with the
prefix {FP=001,TLA=0x0002,NLA=192.1.2.3}/48 and whatever SLA and
Interface ID applies. The converse applies when a host on site A
queries the DNS for a host on site B. IPv6 packets are formed and
transmitted in the normal way within both sites.
_______________________________
Wide Area IPv4 Network
_______________________________
/ 192.1.2.3/ 9.254.253.252 _______________________________/_ ____________________\____________
/ \
IPv4 Site A ########## IPv4 Site B ##########
____________________# 6to4 #_ ____________________# 6to4 #_
# router # # router #
IPv6 Site A ########## IPv6 Site B ##########
2002:c001:0203::/48 2002:09fe:fdfc::/48
_______________________________ _______________________________
_________________________________ _________________________________
Within a 6to4 site, addresses with the 2002::/16 prefix, apart from
those with the local 2002:V4ADDR::/48 prefix, will be handled like
any other non-local IPv6 address, i.e., by a default or explicit
route towards the 6to4 border router.
When an outgoing packet reaches the 6to4 router, it is encapsulated
as defined in Section 3, according to the additional sending rule
defined in Section 5.3. Incoming packets are decapsulated according
to the additional decapsulation rule defined in Section 5.3. The
additional sending and decapsulation rules are the only changes to
IPv6 forwarding, and they occur only at border routers. No IPv4
routing information is imported into IPv6 routing (nor vice versa).
In this scenario, any number of 6to4 sites can interoperate with no
tunnel configuration, and no special requirements from the IPv4
service. All that is required is the appropriate DNS entries and the
additional sending and decapsulation rules configured in the 6to4
router. This router SHOULD also generate the appropriate IPv6 prefix
announcements [CONF, DISC].
Although site A and site B will each need to run IPv6 routing
internally, they do not need to run an IPv6 exterior routing protocol
in this simple scenario; IPv4 exterior routing does the job for them.
It is RECOMMENDED that in any case each site should use only one IPv4
address per 6to4 router, and that should be the address assigned to
the external interface of the 6to4 router. Single-homed sites
therefore SHOULD use only one IPv4 address for 6to4 routing. Multi-
homed sites are discussed briefly in section 5.6.
Because of the lack of configuration, and the distributed deployment
model, there are believed to be no particular scaling issues with the
basic 6to4 mechanism apart from encapsulation overhead.
Specifically, it introduces no new entries in IPv4 routing tables.
5.2 Mixed scenario with relay to native IPv6
During the transition to IPv6 we can expect some sites to fit the
model just described (isolated sites whose only connectivity is the
IPv4 Internet), whereas others will be part of larger islands of
native or tunneled IPv6 using normal IPv6 TLA address space. The
6to4 sites will need connectivity to these native IPv6 islands and
vice versa. In the 6to4 model, this connectivity is accomplished by
IPv6 routers which possess both 6to4 and native IPv6 addresses.
Although they behave essentially as standard IPv6 routers, for the
purposes of this document they are referred to as relay routers to
distinguish them from routers supporting only 6to4, or only native
IPv6.
There must be at least one router acting as a relay between the 6to4
domain and a given native IPv6 domain. There is nothing special
about it; it is simply a normal router which happens to have at least
one logical 6to4 pseudo-interface and at least one other IPv6
interface. Since it is a 6to4 router, it implements the additional
sending and decapsulation rules defined in Section 5.3.
We now have three distinct classes of routing domain to consider:
1. the internal IPv6 routing domain of each 6to4 site;
2. an exterior IPv6 routing domain interconnecting
a given set of 6to4 border routers, including relay routers,
among themselves, i.e., a 6to4 exterior routing domain;
3. the exterior IPv6 routing domain of each native IPv6 island.
1. The internal routing domain of a 6to4 site behaves as described in
section 5.1.
2. There are two deployment options for a 6to4 exterior routing
domain:
2.1 No IPv6 exterior routing protocol is used. The 6to4 routers
using a given relay router each have a default IPv6 route pointing to
the relay router. The relay router MAY apply source address based
filters to accept traffic only from specific 6to4 routers.
2.2 An IPv6 exterior routing protocol is used. The set of 6to4
routers using a given relay router obtain native IPv6 routes from the
relay router using a routing protocol such as BGP4+ [RFC2283,
BGP4+]. The relay router will advertise whatever native IPv6 routing
prefixes are appropriate on its 6to4 pseudo-interface. These
prefixes will indicate the regions of native IPv6 topology that the
relay router is willing to relay to. Their choice is a matter of
routing policy. It is necessary for network operators to carefully
consider desirable traffic patterns and topology when choosing the
scope of such routing advertisements. The relay router will
establish BGP peering only with specific 6to4 routers whose traffic
it is willing to accept.
Although this solution is more complex, it provides effective policy
control, i.e., BGP4+ policy determines which 6to4 routers are able to
use which relay router.
3. A relay router MUST advertise a route to 2002::/16 into the native
IPv6 exterior routing domain. It is a matter of routing policy how
far this routing advertisement of 2002::/16 is propagated in the
native IPv6 routing system. Since there will in general be multiple
relay routers advertising it, network operators will require to
filter it in a managed way. Incorrect policy in this area will lead
to potential unreachability or to perverse traffic patterns.
6to4 prefixes more specific than 2002::/16 must not be propagated in
native IPv6 routing, to prevent pollution of the IPv6 routing table
by elements of the IPv4 routing table. Therefore, a 6to4 site which
also has a native IPv6 connection MUST NOT advertise its 2002::/48
routing prefix on that connection, and all native IPv6 network
operators MUST filter out and discard any 2002:: routing prefix
advertisements longer than /16.
Sites which have at least one native IPv6 connection, in addition to
a 6to4 connection, will therefore have at least one IPv6 prefix which
is not a 2002:: prefix. Such sites' DNS entries will reflect this
and DNS lookups will return multiple addresses. If two such sites
need to interoperate, whether the 6to4 route or the native route will
be used depends on IPv6 address selection by the individual hosts (or
even applications).
Now consider again the example of the previous section. Suppose an
IPv6 host on site B queries the DNS entry for a host on site A, and
the DNS returns multiple IPv6 addresses with different prefixes.
____________________________ ______________________
Wide Area IPv4 Network Native IPv6
Wide Area Network
____________________________ ______________________
/ \ //
192.1.2.3/ 9.254.253.252\ // 2001:0600::/48
____________/_ ____________________\_________//_
/ \ //
########## IPv4 Site B ##########
__# 6to4 #_ ____________________# 6to4 #_
# router # # router #
########## IPv6 Site B ##########
2002:09fe:fdfc::/48
__Site A_____ 2001:0600::/48_________________
as before
______________ _________________________________
If the host picks the 6to4 prefix according to some rule for multiple
prefixes, it will simply send packets to an IPv6 address formed with
the prefix {FP=001,TLA=0x0002,NLA=192.1.2.3}/48. It is essential
that they are sourced from the prefix
{FP=001,TLA=0x0002,NLA=9.254.253.252}/48 for two-way connectivity to
be possible. The address selection mechanism of Section 2.1 will
ensure this.
5.2.1 Variant scenario with ISP relay
The previous scenario assumes that the relay router is provided by a
cooperative 6to4 user site. A variant of this is for an Internet
Service Provider, that already offers native IPv6 connectivity, to
operate a relay router. Technically this is no different from the
previous scenario; site B is simply an internal 6to4 site of the ISP,
possibly containing only one system, i.e., the relay router itself.
5.2.2 Summary of relay router configuration
A relay router participates in IPv6 unicast routing protocols on its
native IPv6 interface and may do so on its 6to4 pseudo-interface, but
these are independent routing domains with separate policies, even if
the same protocol, probably BGP4+, is used in both cases.
A relay router also participates in IPv4 unicast routing protocols on
its IPv4 interface used to support 6to4, but this is not further
discussed here.
On its native IPv6 interface, the relay router MUST advertise a route
to 2002::/16. It MUST NOT advertise a longer 2002:: routing prefix
on that interface. Routing policy within the native IPv6 routing
domain determines the scope of that advertisement, thereby limiting
the visibility of the relay router in that domain.
IPv6 packets received by the relay router whose next hop IPv6 address
matches 2002::/16 will be routed to its 6to4 pseudo-interface and
treated according to the sending rule of Section 5.1.
5.2.2.1. BGP4+ not used
If BGP4+ is not deployed in the 6to4 exterior routing domain (option
2.1 of Section 5.2), the relay router will be configured to accept
and relay all IPv6 traffic only from its client 6to4 sites. Each
6to4 router served by the relay router will be configured with a
default IPv6 route to the relay router (for example, Site A's default
IPv6 route ::/0 would point to the relay router's address under
prefix 2002:09fe:fdfc::/48).
5.2.2.2. BGP4+ used
If BGP4+ is deployed in the 6to4 exterior routing domain (option 2.2
of Section 5.2), the relay router advertises IPv6 native routing
prefixes on its 6to4 pseudo-interface, peering only with the 6to4
routers that it serves. (An alternative is that these routes could
be advertised along with IPv4 routes using BGP4 over IPv4, rather
than by running a separate BGP4+ session.) The specific routes
advertised depend on applicable routing policy, but they must be
chosen from among those reachable through the relay router's native
IPv6 interface. In the simplest case, a default route to the whole
IPv6 address space could be advertised. When multiple relay routers
are in use, more specific routing prefixes would be advertised
according to the desired routing policy. The usage of BGP4+ is
completely standard so is not discussed further in this document.
5.2.2.3. Relay router scaling
Relay routers introduce the potential for scaling issues. In general
a relay router should not attempt to serve more sites than any other
transit router, allowing for the encapsulation overhead.
5.2.3 Unwilling to relay
It may arise that a site has a router with both 6to4 pseudo-
interfaces and native IPv6 interfaces, but is unwilling to act as a
relay router. Such a site MUST NOT advertise any 2002:: routing
prefix into the native IPv6 domain and MUST NOT advertise any native
IPv6 routing prefixes or a default IPv6 route into the 6to4 domain.
Within the 6to4 domain it will behave exactly as in the basic 6to4
scenario of Section 5.1.
5.3 Sending and decapsulation rules
The only change to standard IPv6 forwarding is that every 6to4 router
(and only 6to4 routers) MUST implement the following additional
sending and decapsulation rules.
In the sending rule, "next hop" refers to the next IPv6 node that the
packet will be sent to, which is not necessarily the final
destination, but rather the next IPv6 neighbor indicated by normal
IPv6 routing mechanisms. If the final destination is a 6to4 address,
it will be considered as the next hop for the purpose of this rule.
If the final destination is not a 6to4 address, and is not local, the
next hop indicated by routing will be the 6to4 address of a relay
router.
ADDITIONAL SENDING RULE for 6to4 routers
if the next hop IPv6 address for an IPv6 packet
does match the prefix 2002::/16, and
does not match any prefix of the local site
then
apply any security checks (see Section 8);
encapsulate the packet in IPv4 as in Section 3,
with IPv4 destination address = the NLA value V4ADDR
extracted from the next hop IPv6 address;
queue the packet for IPv4 forwarding.
A simple decapsulation rule for incoming IPv4 packets with protocol
type 41 MUST be implemented:
ADDITIONAL DECAPSULATION RULE for 6to4 routers
apply any security checks (see Section 8);
remove the IPv4 header;
submit the packet to local IPv6 routing.
5.4 Variant scenario with tunnel to IPv6 space
A 6to4 site which has no IPv6 connections to the "native" IPv6
Internet can acquire effective connectivity to the v6 Internet via a
"configured tunnel" (using the terminology in [MECH]) to a
cooperating router which does have IPv6 Access, but which does not
need to be a 6to4 router. Such tunnels could be autoconfigured using
an IPv4 anycast address, but this is outside of the scope of this
document. Alternatively a tunnel broker can be used. This scenario
would be suitable for a small user-managed site.
These mechanisms are not described in detail in this document.
5.5 Fragmented Scenarios
If there are multiple relay routers between native IPv6 and the 6to4
world, different parts of the 6to4 world will be served by different
relays. The only complexity that this introduces is in the scoping
of 2002::/16 routing advertisements within the native IPv6 world.
Like any BGP4+ advertisements, their scope must be correctly defined
by routing policy to ensure that traffic to 2002::/16 follows the
intended paths.
If there are multiple IPv6 stubs all interconnected by 6to4 through
the global IPv4 Internet, this is a simple generalization of the
basic scenarios of sections 5.1. and 5.2 and no new issues arise.
This is shown in the following figure. Subject to consistent
configuration of routing advertisements, there are no known issues
with this scenario.
______________
AS3
_IPv6 Network_ Both AS1 and AS2 advertise
AS1 AS2 2002::/16, but only one of
_____________ them reaches AS3.
// \ __________//_ _\\__________ ______________
6to4 Relay1 6to4 Relay2 IPv6 Network
_____________ _____________ AS4
______________
______________________________________
____________
Global IPv4 Network ----- 6to4 Relay3
________________________________________ _____________
_______ _______ _______ _______
6to4 6to4 6to4 6to4
Site A Site B Site C Site D
________ ________ ________ ________
If multiple IPv6 stubs are interconnected through multiple, disjoint
IPv4 networks (i.e., a fragmented IPv4 world) then the 6to4 world is
also fragmented; this is the one scenario that must be avoided. It
is illustrated below to show why it does not work, since the
2002::/16 advertisement from Relay1 will be invisible to Relay2, and
vice versa. Sites A and B therefore have no connectivity to sites C
and D.
______________
AS3
_IPv6 Network_ Both AS1 and AS2 advertise
AS1 AS2 2002::/16, but sites A and B
_____________ cannot reach C and D.
// \ __________//_ _\\__________
6to4 Relay1 6to4 Relay2
_____________ _____________
_______________ _______________
IPv4 Network IPv4 Network
Segment 1 Segment 2
________________ ________________
_______ _______ _______ _______
6to4 6to4 6to4 6to4
Site A Site B Site C Site D
________ ________ ________ ________
5.6 Multihoming
Sites which are multihomed on IPv4 MAY extend the 6to4 scenario by
using a 2002:: prefix for each IPv4 border router, thereby obtaining
a simple form of IPv6 multihoming by using multiple simultaneous IPv6
prefixes and multiple simultaneous relay routers.
5.7 Transition Considerations
If the above rules for routing advertisements and address selection
are followed, then a site can migrate from using 6to4 to using native
IPv6 connections over a long period of co-existence, with no need to
stop 6to4 until it has ceased to be used. The stages involved are
1. Run IPv6 on site using any suitable implementation. True native
IPv6, [6OVER4], or tunnels are all acceptable.
2. Configure a border router (or router plus IPv4 NAT) connected to
the external IPv4 network to support 6to4, including advertising the
appropriate 2002:: routing prefix locally. Configure IPv6 DNS
entries using this prefix. At this point the 6to4 mechanism is
automatically available, and the site has obtained a "free" IPv6
prefix.
3. Identify a 6to4 relay router willing to relay the site's traffic
to the native IPv6 world. This could either be at another
cooperative 6to4 site, or an ISP service. If no exterior routing
protocol is in use in the 6to4 exterior routing domain, the site's
6to4 router will be configured with a default IPv6 route pointing to
that relay router's 6to4 address. If an exterior routing protocol
such as BGP4+ is in use, the site's 6to4 router will be configured to
establish appropriate BGP peerings.
4. When native external IPv6 connectivity becomes available, add a
second (native) IPv6 prefix to both the border router configuration
and the DNS configuration. At this point, an address selection rule
will determine when 6to4 and when native IPv6 will be used.
5. When 6to4 usage is determined to have ceased (which may be several
years later), remove the 6to4 configuration.
5.8 Coexistence with firewall, NAT or RSIP
The 6to4 mechanisms appear to be unaffected by the presence of a
firewall at the border router.
If the site concerned has very limited global IPv4 address space, and
is running an IPv4 network address translator (NAT), all of the above
mechanisms remain valid. The NAT box must also contain a fully
functional IPv6 router including the 6to4 mechanism. The address
used for V4ADDR will simply be a globally unique IPv4 address
allocated to the NAT. In the example of Section 5.1 above, the 6to4
routers would also be the sites' IPv4 NATs, which would own the
globally unique IPv4 addresses 192.1.2.3 and 9.254.253.252.
Combining a 6to4 router with an IPv4 NAT in this way offers the site
concerned a globally unique IPv6 /48 prefix, automatically, behind
the IPv4 address of the NAT. Thus every host behind the NAT can
become an IPv6 host with no need for additional address space
allocation, and no intervention by the Internet service provider. No
address translation is needed by these IPv6 hosts.
A more complex situation arises if a host is more than one NAT hop
away from the globally unique IPv4 address space, since only the
outermost NAT has a unique IPv4 address. All IPv6 hosts in this
situation must use addresses derived from the 2002: prefix
constructed from the global IPv4 address of the outermost NAT. The
IPv4 addresses of the inner NATs are not globally unique and play no
part in the 6to4 mechanism, and 6to4 encapsulation and decapsulation
can only take place at the outermost NAT.
The Realm-Specific IP (RSIP) mechanism [RSIP] can also co-exist with
6to4. If a 6to4 border router is combined with an RSIP border
router, it can support IPv6 hosts using 6to4 addresses, IPv4 hosts
using RSIP, or dual stack hosts using both. The RSIP function
provides fine-grained management of dynamic global IPv4 address
allocation and the 6to4 function provides a stable IPv6 global
address to each host. As with NAT, the IPv4 address used to
construct the site's 2002: prefix will be one of the global
addresses of the RSIP border router.
5.9 Usage within Intranets
There is nothing to stop the above scenario being deployed within a
private corporate network as part of its internal transition to IPv6;
the corporate IPv4 backbone would serve as the virtual link layer for
individual corporate sites using 2002:: prefixes. The V4ADDR MUST be
a duly allocated global IPv4 address, which MUST be unique within the
private network. The Intranet thereby obtains globally unique IPv6
addresses even if it is internally using private IPv4 addresses [RFC
1918].
5.10 Summary of impact on routing
IGP (site) routing will treat the local site's 2002::/48 prefix
exactly like a native IPv6 site prefix assigned to the local site.
There will also be an IGP route to the generic 2002::/16 prefix,
which will be a route to the site's 6to4 router, unless this is
handled as a default route.
EGP (i.e., BGP) routing will include advertisements for the 2002::/16
prefix from relay routers into the native IPv6 domain, whose scope is
limited by routing policy. This is the only non-native IPv6 prefix
advertised by BGP.
It will be necessary for 6to4 routers to obtain routes to relay
routers in order to access the native IPv6 domain. In the simplest
case there will be a manually configured default IPv6 route to a
relay router's address under the prefix
{FP=001,TLA=0x0002,NLA=V4ADDR}/48, where V4ADDR is the IPv4 address
of the relay router. Such a route could be used to establish a BGP
session for the exchange of additional IPv6 routes.
By construction, unicast IPv6 traffic within a 6to4 domain will
follow exactly the same path as unicast IPv4 traffic.
5.11. Routing loop prevention
Since 6to4 has no impact on IPv4 routing, it cannot induce routing
loops in IPv4. Since 2002: prefixes behave exactly like standard
IPv6 prefixes, they will not create any new mechanisms for routing
loops in IPv6 unless misconfigured. One very dangerous
misconfiguration would be an announcement of the 2002::/16 prefix
into a 6to4 exterior routing domain, since this would attract all
6to4 traffic into the site making the announcement. Its 6to4 router
would then resend non-local 6to4 traffic back out, forming a loop.
The 2002::/16 routing prefix may be legitimately advertised into the
native IPv6 routing domain by a relay router, and into an IPv6 site's
local IPv6 routing domain; hence there is a risk of misconfiguration
causing it to be advertised into a 6to4 exterior routing domain.
To summarize, the 2002::/16 prefix MUST NOT be advertised to a 6to4
exterior routing domain.
6. Multicast and Anycast
It is not possible to assume the general availability of wide-area
IPv4 multicast, so (unlike [6OVER4]) the 6to4 mechanism must assume
only unicast capability in its underlying IPv4 carrier network. An
IPv6 multicast routing protocol is needed [MULTI].
The allocated anycast address space [ANYCAST] is compatible with
2002:: prefixes, i.e., anycast addresses formed with such prefixes
may be used inside a 6to4 site.
7. ICMP messages
ICMP "unreachable" and other messages returned by the IPv4 routing
system will be returned to the 6to4 router that generated a
encapsulated 2002:: packet. However, this router will often be
unable to return an ICMPv6 message to the originating IPv6 node, due
to the lack of sufficient information in the "unreachable" message.
This means that the IPv4 network will appear as an undiagnosable link
layer for IPv6 operational purposes. Other considerations are as
described in Section 4.1.3 of [MECH].
8. IANA Considerations
No assignments by the IANA are required beyond the special TLA value
0x0002 already assigned.
9. Security Considerations
Implementors should be aware that, in addition to possible attacks
against IPv6, security attacks against IPv4 must also be considered.
Use of IP security at both IPv4 and IPv6 levels should nevertheless
be avoided, for efficiency reasons. For example, if IPv6 is running
encrypted, encryption of IPv4 would be redundant except if traffic
analysis is felt to be a threat. If IPv6 is running authenticated,
then authentication of IPv4 will add little. Conversely, IPv4
security will not protect IPv6 traffic once it leaves the 6to4
domain. Therefore, implementing IPv6 security is required even if
IPv4 security is available.
By default, 6to4 traffic will be accepted and decapsulated from any
source from which regular IPv4 traffic is accepted. If this is for
any reason felt to be a security risk (for example, if IPv6 spoofing
is felt to be more likely than IPv4 spoofing), then additional source
address based packet filtering could be applied. A possible
plausibility check is whether the encapsulating IPv4 address is
consistent with the encapsulated 2002:: address. If this check is
applied, exceptions to it must be configured to admit traffic from
relay routers (Section 5). 2002:: traffic must also be excepted from
checks applied to prevent spoofing of "6 over 4" traffic [6OVER4].
In any case, any 6to4 traffic whose source or destination address
embeds a V4ADDR which is not in the format of a global unicast
address MUST be silently discarded by both encapsulators and
decapsulators. Specifically, this means that IPv4 addresses defined
in [RFC1918], broadcast, subnet broadcast, multicast and loopback
addresses are unacceptable.
Acknowledgements
The basic idea presented above is probably not original, and we have
had invaluable comments from Magnus Ahltorp, Harald Alvestrand, Jim
Bound, Scott Bradner, Randy Bush, Matt Crawford, Richard Draves,
Jun-ichiro itojun Hagino, Joel Halpern, Tony Hain, Andy Hazeltine,
Bob Hinden, Geoff Huston, Perry Metzger, Thomas Narten, Erik
Nordmark, Markku Savela, Ole Troan, Sowmini Varadhan, members of the
Compaq IPv6 engineering team, and other members of the NGTRANS
working group. Some text has been copied from [6OVER4]. George
Tsirtsis kindly drafted two of the diagrams.
References
[AARCH] Hinden, R. and S. Deering, "IP Version 6 Addressing
Architecture", RFC2373, July 1998.
[AGGR] Hinden., R, O'Dell, M. and S. Deering, "An IPv6
Aggregatable Global Unicast Address Format", RFC2374,
July 1998.
[API] Gilligan, R., Thomson, S., Bound, J. and W. Stevens,
"Basic Socket Interface Extensions for IPv6", RFC2553,
March 1999.
[BGP4+] Marques, P. and F. Dupont, "Use of BGP-4 Multiprotocol
Extensions for IPv6 Inter-Domain Routing", RFC2545, March
1999.
[CONF] Thomson, S. and T. Narten, "IPv6 Stateless Address
Autoconfiguration", RFC2462, December 1998.
[DISC] Narten, T., Nordmark, E. and W. Simpson, "Neighbor
Discovery for IP Version 6 (IPv6)", RFC2461, December
1998.
[IPV6] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", RFC2460, December 1998.
[6OVER4] Carpenter, B. and C. Jung, "Transmission of IPv6 over IPv4
Domains without Explicit Tunnels", RFC2529, March 1999.
[ANYCAST] Johnson, D. and S. Deering, "Reserved IPv6 Subnet Anycast
Addresses", Work in Progress.
[MULTI] Thaler, D., "Support for Multicast over 6to4 Networks",
Work in Progress.
[SCALE] Hain, T., "6to4-relay discovery and scaling", Work in
Progress.
[SELECT] Draves, R., "Default Address Selection for IPv6", Work in
Progress.
[RFC791] Postel, J., "Internet Protocol", STD 5, RFC791, September
1981.
[RFC1918] Rekhter, Y., Moskowitz, R., Karrenberg, D., de Groot, G.
and E. Lear, "Address Allocation for Private Internets",
BCP 5, RFC1918, February 1996.
[MECH] Gilligan, R. and E. Nordmark, "Transition Mechanisms for
IPv6 Hosts and Routers", RFC2893, August 2000.
[RSIP] Borella, M., Grabelsky, D., Lo, J. and K. Tuniguchi,
"Realm Specific IP: Protocol Specification", Work in
Progress.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC2119, March 1997.
[RFC2283] Bates, T., Chandra, R., Katz, D. and Y. Rekhter,
"Multiprotocol Extensions for BGP-4", RFC2283, February
1998.
Authors' Addresses
Brian E. Carpenter
IBM
iCAIR, Suite 150
1890 Maple Avenue
Evanston IL 60201, USA
EMail:
brian@icair.org
Keith Moore
UT Computer Science Department
1122 Volunteer Blvd, Ste 203
Knoxville, TN 37996-3450
USA
EMail: moore@cs.utk.edu
Intellectual Property
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11. Copies of
claims of rights made available for publication and any assurances of
licenses to be made available, or the result of an attempt made to
obtain a general license or permission for the use of such
proprietary rights by implementors or users of this specification can
be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights which may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive
Director.
Full Copyright Statement
Copyright (C) The Internet Society (2001). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Acknowledgement
Funding for the RFCEditor function is currently provided by the
Internet Society.
