前一段时间在solaris9 x86安装过一个8139网卡驱动,当时没有写文档，前几天有个朋友需要帮忙安装8139网卡驱动，而且论坛上也有很多朋友问此类的问题，非常遗憾！！！这次安装D-LINK DFE-530TX网卡驱动成功以后，把主要的步骤写出来，主要是从解决solaris9 x86安装不兼容网卡的思路上对大家有所帮助！！！！
一、 基本信息：
1、 PC基本硬件信息：
微星主板;P4 1.8MHZ，内存512MB，硬盘40GB，网卡：D-LINK DFE-530TX，显卡： nvidia RIVA TNT2
2、 操作系统信息：windows 2000 ＋solaris9 x86
3、 现有状况：windows 2000 和solaris9 x86都已安装成功，win2000也能够上网，但是solaris9能够正常启动，但是网卡不能正常工作。
二、 solaris9 x86安装网卡D-LINK DFE-530TX过程：
1、 使用sys-unconfig命令还是不能找到网卡。
用sys-unconfig命令可以改变主机名、时区等，但是不能设置网络信息。
郁闷啊！！！
2、 从http://www.solaris-x86.org/ 网站查看solaris9 x86兼容性列表：
http://www.sun.com/bigadmin/hcl/data/9/components/views/networking.html
发现solaris9 x86不兼容D-LINKD-LINK DFE-530TX。
哦！！我可以到D-LINK网站下载驱动！！嘿嘿！！
3、 从D-LINK网站查找D-LINK DFE-530TX对于solaris的驱动程序：http://support.dlink.com/products/view.asp?productid=DFE%2D530TX
但是D-LINK DFE-530TX没有对unix系统支持的网卡驱动。
老天啊！！！
4、 从solaris http://solaris-x86.org/software/drivers/网站找一下：
发现里面有很多网卡的驱动程序啊！！！http://homepage2.nifty.com/mrym3/taiyodo/rh-1.0.9.tar.gz
下载D-LINK DFE-530TX驱动程序
5、 安装D-LINK DFE-530TX驱动过程
由于网络不通只能刻盘（问题：不知道usb可不可以使用啊？），100K的文件我刻了一张盘（呜呜呜！！好惨啊！！）
拷贝文件到系统上
＃gzip –d rh-1.0.9.tar.gz
#tar xvf rh-1.0.9.tar
cd rh-1.0.9
查看README.txt
安装驱动程序：
1）# /usr/ccs/bin/make install
/usr/sbin/install -f /kernel/drv -m 755 -u root -g sys ./i386/rh
new owner is root
./i386/rh installed as /kernel/drv/rh
cp /etc/system /etc/system.norh
echo "exclude: rh" >> /etc/system.norh
2）# ./adddrv.sh
exit status = 0
System configuration files modified but rh driver not loaded or attached.
Driver (rh) installed.
3）# modload obj/rh
4）# devfsadm -i rh
5）# ifconfig rh0 plumb
6）# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
rh0: flags=1000842<BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
ether 0:40:5:15:88:dc
# ifconfig rh0 192.0.0.160 netmask 255.255.255.252 up
# route add default 192.0.0.10
6、 测试正常
# ping 192.0.0.160
192.0.0.160 is alive
# ping 192.0.0.10
192.0.0.10 is alive
三、solaris9存在问题：
1、 不知道usb可不可以使用啊？
如果可以，可以帮助很多朋友把下载的驱动传到solaris9上！！而不用刻盘了！！希望有朋友能够补充usb使用方法？
2、 solaris9 X86启动需要人工干预（按n多的F2），很是不爽，有没有好的方法，让他自己启动？希望有朋友能够补充
四、附件：从http://solaris-x86.org/网站可下载的网卡驱动程序：
solaris X86网卡驱动下载网址：
http://homepage2.nifty.com/mrym3/taiyodo/eng/index.htm
可支持的网卡驱动类型：找到相应的网卡驱动，按照readme文件安装应该就可以！！
Free NIC drivers for Solaris
________________________________________
What's new?
07/04/2004 bcf updated and ni supported PnP ISA NE2000.
05/03/2004 Rh fixed for invalid mac address problem in built-in rhine II.
04/01/2004 VIA rhine driver was updated and released under the BSD license.
01/30/2004 PCMCIA NE2000 driver (pcni) ready for solaris9
01/19/2004 sis900/dp83815 driver updated. The previous revisions may panic the system under heavy ethernet traffic.
________________________________________
CAUTION: They are NO WARRANTY and distributed under LGPL or the BSD license.
0. General Descriptions
As device drivers are loaded in the kernel space, they may cause serious problems i.e. panic or system hang. Please ensure that the driver works fine before you install it into /kernel directory. Some testing methods are described in README in the distributions.
I started some following works with porting Linux nic drivers into Solaris. But I have re-written all of them not to use Linux driver codes, as I was pointed out that it was violation of GPL to link GPL drivers into properiety kernel.
Now licensing of the drivers is under changing. Formerly the drivers were distributed under LGPL, but the new releases will be distributed under the BSD license.
For sparc platforms, it needs solaris8 10/01 or later. You also need C compiler, escpecially gcc3.x to make 64bit binaries, as compiled binaries for sparc are not included in the distributions. You can also use C compilers in Sun products.
For x86 platforms, it needs to disable PnP OS or ACPI in BIOS setting to avoid incorrect IRQ assignment problem in Solaris x86. You also should assign IRQs to all devices on board in BIOS setting even if Solaris doesn't use them.
1. pctc driver for 3COM 3C589 PCMCIA cards
This is an alternative of Solaris pcelx driver which did not work with E version of 589 cards. But now a work around is known for pcelx, that is creating /kernel/drv/pcelx.conf file that includes following line.
force-8bit=1;
If you are interrested in a source code, down load below.
Tested OS Version: Solaris8 10/00 x86
Tested Hardware: EtherLink III 3C589C, EtherLink III 3C589D, Megahertz 3C589ET
Source file with x86 binary pctc-0.8.4b.tar.gz (beta test version)
Hot plug is not supported.
2. sfe driver for DP83815 and SiS900 fast ethernet chips
Tested OS version: Solaris8 10/00 x86, Solaris9 12/02 x86, Solaris9 sparc
Tested chips (PCI card product):
DP83815CVNG (Netgear FA311)
DP83815 (HP Pavilion ZE4100, thank to Ben)
DP83815DVNG (NetGear FA311 on sparc, thank to Peter & www.itserv.de)
DP83815 (NetGear FA312 in a Dell PowerEdge 1300, dual 500 MHz cpu's, thank to fred)
SiS900 (Melco BUFFALO LYG-PCI-TXC)
SiS900-core in SiS630ET chip set (thank to Rahul)
SiS900-core in SiS730 chip set (thank to Sytse)
SiS900-core in SiS963 south bridge of SiS648 chip set (thank to Matthias)
It likely work with DP83815 based Netgear FA312 and I-O DATA ET100-PCI-L, but WOL is not supported.
It will work with DP83816 but isn't tested yet.
sfe-1.0.0 or before may panic the system under heavy ethernet traffic. Please use the latest revison.
Source file with x86 binary: sfe-1.0.4.tar.gz
3. rh driver for VIA Rhine family fast ethernet chips
Tested OS version: Solaris8 10/00 x86, Solaris9 12/02 x86, Solaris8 sparc, Solaris9 sparc
Tested chips (PCI card product):
DL10030/VT86C100A (Rhine I), Corega FastEtherII PCI TX
(Thank to Sentil and Koshida)
DL10030, D-Link DFE-530TX (Thank to Chris)
DL10030A, D-Link DFE-530TX (Thank to Vanguard)
VT6102 (Rhine II), Planex communications FNW9702-T3
RhineII in VT8231 South-bridge (VIA EPIA MINI-ITX, model epia-800 motherboard, Thank to Sytse)
RhineII in VT8235 South-bridge (VIA P4MA Pro Mainboard and Biostar's Mainboard, Thank to Jim)
VT6105 (Rhine III), Corega PCI-TXA
Source file with x86 binary: rh-1.0.9.tar.gz
Rh driver is ready for VT6105M chips, but not tested.
4. rf driver for Realtek RTL 8129 / 813x / 810x family fast ethernet chips
Realtek also provides their binay driver. Please refer http://www.realtek.com.tw.
Tested OS version: Solaris8 10/00 x86, Solaris9 12/02 x86, Solaris9 sparc
Tested chips (PCI card product):
RTL8139A (Surecom EPX-320X-R) Thank to Deniz
RTL8139C (Corega, FEther PCI-TXS)
RTL8139D (Surecom EP-320X-R) Thank to Deniz
(HAWKING PN102TX) Thank to Basem
(Corega FEther PCI-TXC plus)
RTL8129 (NDC, NE100TX-E)
RTL8100B (Shuttle AB48N motherboard, need to disable APCI)
MPX EN5038 (Accton EN1207D-TX) Thank to Telewa
It will likely work with D-Link DFE-530TX+, DFE-538TX and other RTL8139 based low cost NIC cards. Now it ready for rtl8101, but not tested.
Source file with x86 binary: rf-1.0.1.tar.gz
5. ni/pcni driver for NE2000 compatible PCI/PCMCIA/PnP ISA ethernet cards
The ni driver was tested under solaris8 10/00 x86 and solaris9 12/02 x86
The pcni driver was tested under solaris8 10/00 x86 but it isn't tested under solaris9.
The ni and pcni drivers are not ready for solaris sparc.
Tested chips (PCI/PCMCIA card product):
PCI Realtek RTL 8029 (Planex communications, ENW-8300-T)
PCI VIA VT 86C926 Amazon (BUFFALO LGY-PCI-TR, Thank to Masato)
PCMCIA Unknown chip (IBM, Credit Card Adapter Ethernet II)
PCMCIA D-Link DL10022 (Planex communications, FNW3600-T)
PCMCIA Winbond W89C926 (Planex communications, ENW3503-T)
PnP ISA Realtek RTL 8019AS (unknown vendor)
Source file with x86 binary: ni-0.
