Network Working Group D. Marlow
Request for Comments: 1768 NSWC-DD
Category: EXPerimental March 1995
Host Group Extensions for CLNP Multicasting
Status of this Memo
This memo defines an Experimental Protocol for the Internet
community. This memo does not specify an Internet standard of any
kind. Discussion and suggestions for improvement are requested.
Distribution of this memo is unlimited.
Abstract
This memo documents work performed in the TUBA (TCP/UDP over Bigger
Addresses) working group of IPng area prior to the July 1994 decision
to utilize SIPP-16 as the basis for IPng. The TUBA group worked on
extending the Internet Protocol suite by the use of ISO 8473 (CLNP)
and its related routing protocols. This memo describes multicast
extensions to CLNP and its related routing protocols for Internet
multicast use. Publication of this memo does not imply acceptance by
any IETF Working Group for the ideas expressed within.
This memo provides a specification for multicast extensions to the
CLNP protocol similar to those provided to IP by RFC1112. These
extensions are intended to provide the mechanisms needed by a host
for multicasting in a CLNP based Internet. This memo covers
addressing extensions to the CLNP addressing strUCture, extensions to
the CLNP protocol and extensions to the ES-IS protocol. An appendix
discusses the differences between IP multicast and the CLNP multicast
approach provided in this memo.
Acknowledgments
The specification provided here was developed by a number of
individuals in the IETF TUBA working group as well as the ANSI X3S3.3
and ISO SC6 WG2 committees. Key contributions were made by Steve
Deering, Joel Halpern, Dave Katz and Dave Oran.
Table of Contents
1. Introduction .......................................... 2
2. Levels of Conformance.................................. 3
3. Group Network Addresses................................ 4
4. Model of a CLNP End System Multicast Implementation.... 8
5. Extensions to the CLNP Protocol........................ 8
6. Extensions to the ES-IS Routeing Protocol ............. 15
7. Security Considerations ............................... 39
Appendix A. Differences with RFC1112 .................... 40
Appendix B. Issues Under Study ........................... 43
References ................................................ 44
Author's Address .......................................... 45
1. Introduction
This memo provides a specification for multicast extensions for CLNP
in order to provide a CLNP based Internet the capabilities provided
for IP by RFC1112 (Host Extensions for IP Multicasting) [RFC1112].
This memo uses an outline similar to that of RFC1112.
Paraphrasing RFC1112, "CLNP multicasting is the transmission of a
CLNP datagram to a "host group", a set of zero or more End Systems
identified by a single group Network address (GNA). A multicast
datagram is delivered to all members of its destination host group
with the same "best-efforts" reliability as regular unicast CLNP
datagrams, i.e., the datagram is not guaranteed to arrive intact at
all members of the destination group or in the same order relative to
other datagrams.
"The membership of a host group is dynamic; that is End Systems may
join and leave groups at any time. There is no restrictions on the
location or number of members in a host group. An End System may be a
member of more than one group at a time. An End System need not be a
member of a group to send datagrams to it.
"A host group may be permanent or transient. A permanent group has an
administratively assigned GNA. It is the address, not the membership
of the group, that is permanent; at any time a permanent group may
have any number of members, even zero.
"Internetwork forwarding of CLNP multicast datagrams is handled by
"multicast capable" Intermediate Systems which may be co-resident
with unicast capable Intermediate Systems.
The multicast extensions to the CLNP addressing structure defines
group Network addresses which identify host groups. The multicast
extensions to CLNP provides a means for identifying a CLNP packet and
provides scope control mechanisms for CLNP multicast packets. The
multicast extensions to the ES-IS protocol provide the mechanisms
needed for a host to exchange control information with multicast
capable routers. These extensions to the ES-IS protocol provide for
a host to "announce" which multicast packets are of interest and for
a multicast capable router to dynamically "map" group Network
addresses to subnetwork addresses.
This memo specifies the extensions required by an End System to make
use of CLNP multicast. In addition the requirements placed upon
multicast capable Intermediate Systems to exchange information with
multicast capable End Systems is specified. No specifications are
provided related to the information exchanges between Intermediate
Systems to support multicast route selection or multicast Protocol
Data Unit (PDU) forwarding. A discussion of multicast route selection
and PDU forwarding has been written by Steve Deering [Deering91].
Note that for these multicast extensions to work there must exist an
uninterrupted path of multicast capable routers between the End
Systems comprising a host group (such paths may utilize tunneling
(i.e., unicast CLNP encapsulated paths between multicast capable CLNP
routers)). In order to support multicast route selection and
forwarding for a CLNP based internet additional specifications are
needed. Specifications of this type could come in the form of new
protocols, extensions to the current CLNP based routing protocols or
use of a technique out of the IETF's Inter-Domain Multicast Routing
(IDMR) group. The IDMR group is currently investigating multicast
protocols for routers which utilize a router's unicast routing
protocols, this approach may extend directly to CLNP routers.
While many of the techniques and assumptions of IP multicasting (as
discussed in RFC1112) are used in CLNP multicasting, there are
number of differences. Appendix A describes the differences between
CLNP multicasting and IP multicasting. This memo describes techniques
brought in directly from projects within ISO to incorporate multicast
transmission capabilities into CLNP [MULT-AMDS].
2. Levels of Conformance
There are three levels of conformance for End Systems to this
specification:
Level 0: no support for CLNP multicasting.
There is no requirement for a CLNP End System (or Intermediate
System) to support CLNP multicasting. Level 0 hosts should be
unaffected by the presence of multicast activity. The destination
addresses used in support of multicast transfers, the GNA, should not
be enabled by a non-multicast capable End System and the PDUs
themselves are marked differently than unicast PDUs and thus should
be quietly discarded.
Level 1: support for sending but not receiving CLNP multicast PDUs.
An End System originating multicast PDUs is required to know whether
a multicast capable Intermediate System is attached to the
subnetwork(s) that it originates multicast PDUs (i.e., to determine
the destination SNPA (subnet) address). An End System with Level 1
conformance is required to implement all parts of this specification
except for those supporting only Multicast Announcement. An End
System is not required to know the current Multicast Address Mapping
to start originating multicast PDUs.
Note: It is possible for End System not implementing Multicast
Address Mapping to successfully originate multicast PDUs (but with
the End System knowing of the existence of a multicast capable
Intermediate System). Such operation may lead to inefficient
subnetworks use. Thus when an End System continues (or may continue)
to originate multicast PDUs destined for the same group,
implementations are to provide Multicast Address Mapping support.
Level 2: full support for CLNP multicasting.
Level 2 allows a host to join and leave host groups as well as send
CLNP PDUs to host groups. It requires implementation by the End
System of all parts of this specification.
3. Group Network Addresses
Individual Network addresses used by CLNP for End System addressing
are called Network Service Access Points (NSAPs). RFC1237 defines
the NSAP address for use in the Internet. In order to provide an
address for a group of End Systems, this specification does not
change the definition of the NSAP address, but adds a new type of
identifier - the group Network address - that supports a multicast
Network service (i.e., between a single source NSAP, identified by an
individual Network address, and a group of destination NSAPs,
identified by a group Network address). Host groups are identified by
group Network addresses.
In the development of multicast address extensions to CLNP,
requirements were identified for: (1)"easily distinguishing" group
addresses at the Network layer from NSAP addresses; (2)leaving the
currently allocated address families unaffected and (3)ensuring that
the approach taken would not require the establishment of new
addressing authorities. In addition, it was agreed that providing
multicast options for all OSI Network layer users was desirable and
thus the group Network addressing solution should support options for
all address formats covered by ISO/IEC 8348 CCITT Recommendation
X.213. The only viable means identified for meeting all requirements
was via creating a new set of AFI values with a fixed one-to-one
mapping between each of the existing AFI values and a corresponding
group AFI value.
Group Network addresses are defined by creating a new set of AFI
values, one for each existing AFI value, and a fixed one-to-one
mapping between each of the existing AFI values and a corresponding
group AFI value. The syntax of a group Network address is identical
to the syntax of an individual Network address, except that the value
of the AFI in an individual Network address may be only one of the
values already allocated for individual Network addresses, whereas
the value of the AFI in a group Network address may be only one of
the values allocated here for group Network addresses. The AFI values
allocated for group Network addresses have been chosen in such a way
that they do not overlap, in the preferred encoding defined by
ISO/IEC 8348 CCITT Recommendation X.213, with any of the AFI values
that have already been allocated for individual Network addresses.
3.1 Definitions
group Network address: an address that identifies a set of zero or
more Network service access points; these may belong to multiple
Network entities, in different End Systems.
individual Network address: an address that identifies a single NSAP.
3.2 CLNP Addresses
A discussion of the CLNP address format is contained in RFC1237. The
structure of all CLNP addresses is divided into two parts the Initial
Domain Part (IDP) and the Domain Specific Part (DSP). The first two
octets of the IDP are the Authority and Format Identifier (AFI)
field. The AFI has an abstract syntax of two hexadecimal digits with
a value in the range of 00 to FF. In addition to identifying the
address authority responsible for allocating a particular address and
the format of the address, the AFI also identifies whether an address
is an individual Network address or a group Network address. There
are 90 possible AFI values to support individual Network address
allocations. In addition, when the AFI value starts with the value
"0" this identifies that the field contains an incomplete individual
Network address (i.e., identifies an escape code).
Table 1 allocates 90 possible AFI values to support group Network
address allocations. In addition if the first two digits of the IDP
are hexadecimal FF, this indicates the presence of an incomplete
group Network address. The allocation of group addresses is
restricted to be only from the AFI values allocated for the
assignment of group addresses in Table 1. An addressing authority in
allocating either Network addresses or authorizing one or more
authorities to allocate addresses, allocates both individual and the
corresponding group addresses. Thus each block of addresses allocated
by an addressing authority (or its sub-authority) contains a block of
individual Network addresses and group Network addresses. The
individual and group address block allocated are differentiated by
the AFI values used which are related as shown in Table 1.
Group Network addresses are only used as the destination address
parameter of a CLNP PDU. Source Address parameters are never
permitted to be group Network addresses.
Table 2 lists the AFI values which have not been assigned, at this
time, for the support of neither individual nor group address
allocation. Future assignment of these AFI values is possible.
Additional information concerning individual Network addresses (i.e.,
NSAP and NET (Network Entity Titles)) is contained in RFC1237.
Note: While the format of the Initial Domain Part of a group Network
address is assigned, the format for the Domain Specific Part of the
group Network address is specified by an addressing authority and is
out of the scope of this memo. While NSAP address assignments are
typically made to support hierarchical unicast routing, a similar
consideration for group Network address assignments may not exist.
TABLE 1 - Relationship of AFI Individual and Group Values
-----------------------------------------------------------
Individual Group Individual Group Individual Group
-----------------------------------------------------------
0x FF
10 A0 40 BE 70 DC
11 A1 41 BF 71 DD
12 A2 42 C0 72 DE
13 A3 43 C1 73 DF
14 A4 44 C2 74 E0
15 A5 45 C3 75 E1
16 A6 46 C4 76 E2
17 A7 47 C5 77 E3
18 A8 48 C6 78 E4
19 A9 49 C7 79 E5
20 AA 50 C8 80 E6
21 AB 51 C9 81 E7
22 AC 52 CA 82 E8
23 AD 53 CB 83 E9
24 AE 54 CC 84 EA
25 AF 55 CD 85 EB
26 B0 56 CE 86 EC
27 B1 57 CF 87 ED
28 B2 58 D0 88 EE
29 B3 59 D1 89 EF
30 B4 60 D2 90 F0
31 B5 61 D3 91 F1
32 B6 62 D4 92 F2
33 B7 63 D5 93 F3
34 B8 64 D6 94 F4
35 B9 65 D7 95 F5
36 BA 66 D8 96 F6
37 BB 67 D9 97 F7
38 BC 68 DA 98 F8
39 BD 69 DB 99 F9
-----------------------------------------------------------
TABLE 2 - AFI values reserved for future allocation
--------------
1A-1F
2A-2F
3A-3F
4A-4F
5A-5F
6A-6F
7A-7F
8A-8F
9A-9F
FA-FE
--------------
4. Model of a CLNP End System Multicast Implementation
The use of multicast transmission by a CLNP End System involves
extensions to two protocols: CLNP and the ES-IS Routeing Protocol. To
provide level 0 service (no support for CLNP multicast), no
extensions to these two protocols are required. To provide level 1
service (support for sending but not receiving CLNP multicast PDUs)
all extensions contained in the following sections are required
except for those supporting only Multicast Announcement. In order to
support level 2 service (full support for CLNP multicasting), the
extensions contained in the following sections are required.
Extensions identified for Intermediate Systems are not required (or
appropriate) for End Systems. Multicast transmission also requires
the use of a group Network address (as previously described) as the
destination address parameter.
5. Extensions to the CLNP protocol
This section provides extensions to the CLNP Protocol [CLNP] ISO
8473-1, to support multicast transmission. These additions provide
procedures for the connectionless transmission of data and control
information from one network-entity to one or more peer network-
entities.
In developing the multicast extensions for CLNP a decision was needed
on how to "mark" a packet as multicast (versus the current unicast
packets). Such marking is necessary since the forwarding behavior
for multicast packets is different (e.g., multiple copies of a packet
may need to be forwarded). The two alternatives considered were to
mark the packet (via a particular field) or to mark the destination
address, in the end both were done. The destination address for a
multicast PDU identifies a host group which is of a very different
nature than the unicast NSAP address. Rather than changing the
nature of NSAP addresses, a new set of addresses were created named
group Network addresses which are marked within the first octet
(i.e., the AFI field) with values reserved for group Network
addresses.
Consideration was given to no further marking of the PDU; however, a
problem was identified with only using the group Network address to
identify multicast packets. Currently routers implementing the IS-IS
Intra-Domain protocol as Level 1 routers when receiving a packet with
an unknown destination address are permitted to either discard the
packet or send it to a Level 2 router. Such actions by non-multicast
capable routers to multicast packets can lead to non-deterministic
behavior. Level 1 routers upon receiving a packet containing a group
Network address might pass the packet up to a Level 2 router (which
may or may not be multicast capable) or it might discard it.
Depending upon the circumstances this might lead to whole regions
missing packets or packet duplication (possibly even explosion). The
result was to seek deterministic behavior by non-multicast capable
routers by creating a new PDU type (Multicast Data PDU) and inserting
into the CLNP reasons for discard: receiving a PDU of unknown type.
Note that this reason for discard is mandatory on multicast capable
and non-multicast capable CLNP implementations.
5.1 Definitions
multicast: Data transmission to one or more destinations in a
selected group in a single service invocation.
multicast capable Intermediate System: An Intermediate System which
incorporates the multicast features of the Network layer.
5.2 Addresses
The destination address parameter of a multicast PDU shall contain a
group Network address. The source address parameter shall be an
individual Network address.
5.3 Extensions to the current protocol functions
In order to support multicast transmissions the following optional
CLNP protocol functions will be implemented:
5.3.1 Header Format Analysis function
The header format analysis function optionally provides capabilities
to Network entities which support multicast transfer to supply
applicable PDUs directly to End Systems served by such a Network
entity as well as to forward such PDUs on to other Network entities.
This optional functionality is realized through a Network entity with
multicast capability identifying a PDU as using multicast transfer
via the PDU type and the PDU's destination address field.
If a Network entity supports multicast transmission, then the header
format analysis function shall provide checking to ensure that a PDU
does not contain a group Network address in the source address field.
Any PDU header analyzed to have a group address in the source address
field shall be discarded.
5.3.2 Route PDU function
The route PDU function optionally provides capabilities to Network
entities which support multicast transfer for determining multiple
Network entities to which a single PDU shall be forwarded to. This
may result in multiple invocations of the forward PDU function and
hence the need to make multiple copies of the PDU. For PDUs that are
received from a different Network entity, the optional functionality
for the route PDU function is realized as a result of the header
format analysis function's recognition of the PDU as being a
multicast PDU. A Network entity attached to more than one subnetwork
when originating a multicast PDU is permitted to originate the PDU on
more than one subnetwork.
Note: The ES-IS function "Extensions to the ISO CLNP Route Function
by End Systems" discussed in section 6.10 identifies on which
subnetworks an End System attached to more than one subnetwork must
originate multicast PDUs on.
Note: The purpose in allowing an originating Network entity to
originate a multicast PDU on multiple subnetworks is to support the
development of multicast IS-IS protocols which will need to determine
on which subnetworks a multicast PDU has visited. This behavior is
predicated on the assumption that the Intermediate Systems in the OSI
environment performing multicast forwarding form a connected set.
5.3.3 Forward PDU function
This function issues an SN-UNITDATA request primitive, supplying the
subnetwork or Subnetwork Dependent Convergence Function (SNDCF)
identified by the route PDU function with the protocol data unit as
user data to be transmitted, the address information required by that
subnetwork or SNDCF to identify the "next" system or systems within
the subnetwork-specific addressing domain (this may be one or more
Intermediate Systems and/or one or more destination End Systems), and
quality of service constraints (if any) to be considered in the
processing of the user data.
5.3.4 Discard PDU function
Add an additional reason for discard - a PDU is received with an
unknown type code.
5.3.5 Error reporting function
It is important to carefully control the use of the error reporting
capability in the case of multicast transfers. The primary concern
is to avoid the occurrence of broadcast storms and thus a multicast
PDU may not cause the origination of another multicast PDU. This is
the primary reason that the source address is not permitted to be a
group address. In addition, a multicast PDU with error reporting
permitted can result in flooding the source network-entity (as well
as the networks used) with Error Report PDUs.
While error reports are permitted on multicast PDUs, a PDU with a
group Network address in the source address field shall not be
responded to with an Error Report. This is to ensure that a multicast
PDU does not generate another multicast PDU. If the source address is
identified as a group address then an error report PDU shall not be
generated and the original PDU shall be discarded.
5.3.6 Source routing functions
No source routing capability is provided for multicast PDU transfer.
The NS provider shall not accept a multicast PDU with source route
parameters.
5.4 Scope control function
5.4.1 Overview
The scope control function is an option for multicast PDU forwarding
only. The scope control function allows the originator to limit the
forwarding of the multicast PDU. The scope control function provides
the capability to limit the relaying of a particular PDU based on the
individual Network addressing hierarchy and/or limit the amount of
multicast expansion which can take place. In cases where both forms
of scope control are applied to the same PDU, forwarding will cease
once either has reached its scope control limit.
5.4.2 Prefix Based Scope Control
The prefix based scope control function allows the originator to
specify a specific set of address prefixes where the multicast
forwarding of a PDU by an Intermediate System occurs only if one of
the prefixes matches the Network Entity Title (NET) of the
Intermediate System. Prefix based scope control may be selected only
by the originator of a PDU. Prefix based scope control is
accomplished using one or more address prefixes held in a parameter
within the options part of the PDU header. The length of this
parameter is determined by the originating network entity, and does
not change during the lifetime of a PDU.
When an Intermediate System receives a multicast PDU containing a
prefix based scope control parameter, forwarding is only performed if
every octet of one of the prefixes contained in the prefix based
scope control parameter matches that Intermediate System's NET,
starting from the beginning of its NET. If no such prefix match
exists, the Intermediate System discards the PDU. The error reporting
function shall not be invoked upon PDU discard.
5.4.3 Radius Scope Control
The radius scope control function allows the originator to specify a
maximum logical distance where multicast expansion can occur. It is
closely associated with the header format analysis function. Each IS
receiving a multicast PDU which is capable of expanding and which
contains a Radius Scope Control parameter, decrements the Radius
Scope Control field in the PDU by an administratively set amount
between 0 and the maximum value of the field. An IS, when it
decrements the Radius Scope Control field, shall place a value of 0
into this field if its current value is less than the amount it is to
decrement by. This function determines whether the PDU received may
be forwarded or whether its Radius has been reached, in which case it
shall be discarded. An Intermediate System shall not forward a
multicast PDU containing a Radius Scope Control parameter with a
value of 0. The error reporting function shall not be invoked upon
PDU discard.
5.4.3.1 Radius Scope Control Example
The Radius Scope Control parameter is useful where policies have been
established across the potential forwarding path. One possible
policy for Internet use is for multicast capable routers to treat
this field as a hop count within a domain (decrement by one unit) and
for inter-domain routers to either decrement this field to an even
multiple of 256 when crossing domains where prior agreements have
been made or decrement this field to 0 (i.e., discard the packet) for
other domains.
5.5 Structure and Encoding of PDUs
Multicast transmission is accomplished via the transfer of Multicast
Data (MD) PDUs. The PDU type code for a MD PDU is "1 1 1 0 1". The
format of the MD PDU is identical to that of the Data (DT) PDU. The
MD and DT PDU may contain the same optional parameters with the
following exceptions: (1)The source routing parameter is permitted
within DT PDUs but not MD PDUs; and (2)The scope control parameter is
permitted within MD PDUs but not DT PDUs.
5.6 Optional parameters for multicast support
5.6.1 Prefix Based Scope Control
The prefix based scope control parameter specifies one or more
address prefixes for which Intermediate System forwarding requires a
match of one of the contained prefixes with the beginning of the
Intermediate System's NET.
Parameter Code: 1100 0100
Parameter Length: variable
Parameter Value: a concatenation of address prefix entries
The parameter value contains an address prefix list. The list
consists of variable length address prefix entries. The first octet
of each entry gives the length of the address prefix denominated in
bits that comprises the remainder of the entry. If the length field
does not specify an integral number of octets then the prefix entry
is followed by enough trailing zeroes to make the end of the entry
fall on an octet boundary. The list must contain at least one entry.
The prefix shall end on a boundary that is legal in the abstract
syntax of the address family from which it is derived. For example,
the encoding of a prefix whose DSP is expressed in decimal syntax
must end on a semi-octet boundary, while the encoding of a prefix
whose DSP is expressed in binary syntax can end on an arbitrary bit
boundary. If the end of the prefix falls within the IDP, then the
prefix must end on a semi-octet boundary and must not contain any
padding characters.
Note: The length of the prefix based scope control parameter is
determined by the originator of the PDU and is not changed during the
lifetime of the PDU.
5.6.1.1 Prefix matching
A prefix that extends into the DSP shall be compared directly against
the encoded NET address, including any padding characters that may be
present. A prefix which does not extend into the DSP shall be
compared against the derived quantity NET', which is oBTained from
the NET address by removing all padding characters (as defined by the
binary encoding process of ISO 8348).
The existence of a match shall be determined as follows:
a) If the encoded NET (or NET') contains fewer bits than the pre-
fix, then there is no match.
b) If the encoded NET (or NET') contains at least as many bits as
the prefix, and all bits of the prefix are identical to the
corresponding leading bits of the encoded NET (or NET'), there
is a match. Otherwise, there is no match.
5.6.2 Radius Scope Control
The radius scope control parameter specifies the logical distance
that a multicast PDU can be forwarded.
Parameter Code: 1100 0110
Parameter Length: two octets
Parameter Value: two octets which represents the remaining
distance, that the PDU can be forwarded,
in administratively set units.
5.7 Provision of the Underlying Service
For a subnetwork that provides an inherent multicast capability, it
is the functionality of the SNDCF to provide the mapping between
group Network addresses and the corresponding addressing capability
of the subnetwork.
5.8 Conformance
All of the extensions provided to the functions to support multicast
capability are optional. For an End System or Intermediate System
which is not multicast capable these extensions are not applicable.
An implementation claiming conformance as a multicast capable End
System shall meet all of the requirements for an End System which is
not multicast capable and also provide all of the multicast
extensions provided here. An implementation claiming conformance as a
multicast capable Intermediate System shall meet all of the
requirements for an Intermediate System which is not multicast
capable and also provide all of the multicast extensions provided
here.
6. Extensions to the ES-IS Routeing Protocol
This section provides optional extensions to the ES-IS Routeing
Protocol [ES-IS], ISO 9542 to support the transfer of multicast PDUs.
It is an explicit goal of this specification that ESs and ISs, some
of which will have multicast capabilities and some without, will be
able to fully function on the same subnetworks. This specification
does not change any ASPect of a currently defined (i.e., non-
multicast) ISO 9542 implementation, it adds new optional
functionality not modifying current functionality. Two basic
functions are provided: multicast announcement and multicast address
mapping.
6.1 Overview of the protocol
6.1.1 Operation of ESs receiving multicast PDUs
ESs, upon initialization and periodically thereafter, will construct
End System Group Hello (ESGH) PDUs identifying, by particular group
Network addresses, the multicast PDUs it wishes to receive. The ES
will periodically originate (announce) these ESGH PDUs on the
subnetwork it wishes to receive these on. Reporting the same group
Network address on multiple subnetworks may result in the reception
of duplicate PDUs. ES-IS operations related to requesting the same
group Network address on multiple subnetworks are handled totally
independently (e.g., using different logical timers,...). It is
permitted for an ES to report a number of group Network addresses in
the same ESGH PDU. The only restrictions placed on providing
multiple group Network addresses within the same ESGH PDU are that
all packets requested are to be received on the same subnet, with the
same holding time and that the ESGH PDU be of length equal to or less
that its maximum packet size constraint. Note that each group
Network address in the ESGH PDU is paired with its own SNPA
(subnetwork point of attachment) address.
An ES will always have an SNPA address associated with each of its
active group Network addresses. An SNPA address is a subnetwork
address, in the case of a subnetwork which uses IEEE 802 addresses
the SNPA address is a 48 bit IEEE 802 MAC (media access control)
address. Of particular interest is the address used to mark the
destination group. For a subnetwork using IEEE 802 addressing a
group SNPA address uses a particular bit position to "mark" group
SNPA addresses.
Upon initialization the ES may have static SNPA address associations
(Pre-configured SNPA addresses). For any group Network address
without a Pre-configured SNPA address that the ES wishes to receive,
the ES will associate the "All Multicast Capable End Systems" SNPA
address. Upon receiving a Multicast Address Mapping (MAM) PDU
containing a group Network address that the ES is announcing, the ES
will use the SNPA address pairing contained in the MAM PDU for that
group Network address. Upon the expiration of the Mapping Holding
Timer, the ES shall revert back to associating either the Pre-
configured SNPA address if one exists or the "All Multicast Capable
End Systems" SNPA address for the specific group Network address.
While an ES is permitted to listen in on other ESs announcements
(needed for the damping option), an ES is not permitted to change its
group Network address to SNPA address mapping based on the
announcement of other ESs.
Optionally, the ES may perform damping (resetting a Multicast
Announcement Timer corresponding to a particular group Network
address) if the conditions necessary to withhold a particular
announcement are met. In order to perform damping the following
conditions must be met: (1)The ES must be processing other ES's
announcements; (2)An ESGH PDU is received that identifies the exact
same group Network address and SNPA address pairing on a particular
subnetwork that this ES is announcing on; (3) The Multicast Holding
Timer parameter value in the ESGH PDU received is equal to or greater
than the Multicast Holding Timer value, for this subnetwork, that is
being used by the ES processing this ESGH PDU.
ESs will utilize a local default value for their Multicast
Announcement Timer to control the period for sending out their ESGH
PDUs. The Active Multicast IS, if one exists on a particular
subnetwork, may suggest a value for ESs on the subnetwork to use for
their Multicast Announcement Timer for a specific group Network
address. In order to support the optional damping function, ESs are
required to incorporate a 25% jittering to the timer values that they
are using.
6.1.2 Operation of ESs originating multicast PDUs
The ES originating multicast packets identified by a specific group
Network address is not required to be a receiver of such packets (and
thus is not announcing that particular group Network address). The
origination of multicast PDUs involves two differences to the
origination of unicast PDUs. The two differences are: (1)The
mechanism for selecting a destination SNPA address and (2)For End
Systems attached to more than one subnet, the decision on which
subnet(s) to originate the PDUs.
The destination SNPA address used for originating each multicast
packet depends on whether there is a multicast capable IS attached to
the subnetworks. When a multicast capable IS is attached, the
decision depends on whether there is multicast address mapping
information available for that subnetwork corresponding to the group
Network address used as the destination address parameter of the
multicast packet. When there is a multicast capable IS attached to a
subnetwork and there is multicast address mapping information
available corresponding to the group Network address, then the SNPA
address obtained from the multicast address mapping information is
used. Originating multicast packets using the destination SNPA
address used for receiving such multicast packets ensures that the
multicast packets will not require additional forwarding on the
originating subnetwork(s). When there is a multicast capable IS
attached to a subnetwork but for which there is no multicast address
mapping information available corresponding to the the group Network
address, then the SNPA address used is the "All Multicast Capable
Intermediate Systems" address.
When there is no multicast capable IS attached to a subnetwork then
the ES originating a multicast PDU uses pre-configured information if
it is available or the "All Multicast Capable End Systems" SNPA
address when no pre-configured information is available.
ES's attached to more than one subnetwork forward each multicast
packet that they originate onto every attached subnetwork for which
the NSAP address being used as the source address of the multicast
packet is actively being reported through the unicast ES-IS Report
Configuration function.
6.1.3 Operation of the Active Multicast IS
The Active Multicast IS listens in on all ESGH PDUs originated on the
subnetwork for which it is serving as the Active Multicast IS. All
subnetworks are handled independently (even if multiple subnetworks
have the same ESs attached and the IS is serving as the Active
Multicast IS for these subnetworks).
The Active Multicast IS originates MAM PDUs, for all group Network
addresses for which it has received ESGH PDUs, on the subnetwork due
to the following operational conditions:
1) The IS initializes either as the Active Multicast IS after an
election with other multicast capable ISs or initializes
believing it is the only multicast capable IS;
Note: The determination of such conditions is outside of the scope of
this specification;
2) The IS receives an ESGH PDU with a group Network address paired
to an incorrect SNPA address;
3) The expiration of the IS's Multicast Address Mapping Timer for
that group Network address; or
Note: This is to prevent the expiration of Mapping Holding Timers in
ESs.
4) The IS receives a multicast PDU originated on the subnetwork
which used an incorrect destination SNPA address.
Note: Of particular concern are those multicast packets using the
"All Multicast Capable Intermediate Systems" SNPA address when
another SNPA address should have been used. In addition the
multicast capable ISs are responsible for listening in on all
multicast packets using destination SNPA addresses that are contained
within the current multicast address mapping information.
As a result of the event driven conditions (i.e., conditions 2 or 4
above), the Active Multicast IS sends a MAM PDU with direct
information (i.e., not needing analysis of the Mask parameters). The
Active Multicast IS limits the number of MAM PDUs that are sent out
per unit of time. Particular MAM PDUs with direct information will
not be sent more than once per second. MAM PDU will be sent in
response to continuing event driven conditions such that events
occurring greater than 10 seconds after the issuance of such a MAM
PDU will result in the issuance of another MAM PDU.
The Active Multicast IS is responsible for forwarding a multicast
packet back on the subnetwork it was originated when a multicast
packet used the "All Multicast Capable Intermediate System" SNPA
address when another SNPA address should have been used. A packet
forwarded back onto the subnetwork the multicast packet was
originated on will be given a CLNP Lifetime of "1" to prevent the
continued relaying of duplicate packets by the multicast ISs.
The further relaying of any multicast packet originated on a
subnetwork is the responsibility of the multicast routing protocol
used and is outside the scope of this specification.
6.2 Definitions
Active Multicast IS: The one multicast capable IS selected (via means
outside of this specification) to originate Multicast Address Mapping
information on a particular subnetwork.
Paired SNPA Address: The SNPA address associated with a particular
group Network address on a specific subnetwork.
6.3 Routing information supporting multicast transmission
6.3.1 Multicast Announcement Information
An IS should forward a multicast PDU containing a particular
destination group Network address onto a subnetwork to which it is
attached if and only if one or more of the ESs attached to that
subnetwork have declared an interest in receiving multicast PDUs
destined for that group Network address. Multicast announcement
information enables an IS that supports CLNP multicast to dynamically
discover, for each subnetwork to which it is attached, the group
Network addresses for which ESs attached to that subnetwork have
declared an interest.
On a point-to-point subnetwork the multicast announcement information
informs the Network entity, in the case where it is attached to an
End System, of the group Network addresses for which that End System
expects to receive multicast PDUs.
On a broadcast subnetwork the multicast announcement information
informs the multicast capable Intermediate Systems, of the group
Network addresses for which ESs attached to that subnetwork expect to
receive multicast PDUs.
Note: Intermediate Systems with the optional OSI multicast
capabilities do receive information identifying the SNPA address of
ESs on the broadcast network that want PDUs with particular group
Network addresses as their destination address; however, the critical
information is which multicast PDUs are needed, not which ESs need
them.
6.3.2 Multicast Address Mapping Information
In order to receive multicast packets destined for a particular group
Network address, an ES may need to associate with the group Network
address a specific SNPA address. Multicast address mapping
information enables an IS to inform ESs that they can receive
multicast packets destined for a particular group Network address on
a corresponding specific SNPA address. In addition, multicast
address mapping information may provide the specific destination SNPA
addresses needed by an ES for originating multicast packets.
Multicast address mapping information is not employed on point-to-
point subnetworks.
Multicast address mapping information is employed on broadcast sub-
networks to enable multicast capable Intermediate Systems to inform
the multicast capable End Systems that they can receive, on a
specific broadcast subnetwork, multicast packets destined for a
particular group Network address on a corresponding specific SNPA
address. In addition multicast address mapping information provides
the specific destination SNPA address, that corresponds to a
particular group Network address, for each multicast packet that it
originates on a specific broadcast subnetwork.
6.4 Addresses
All exchanges using this protocol are accomplished over a single
subnetwork. While the control PDU's contain Network addresses (i.e.,
group Network addresses) actual control PDU transfer is accomplished
via Subnetwork based group addresses (i.e., group SNPA addresses).
The following group SNPA addresses are used: (1)All Multicast Capable
End Systems; (2)All Multicast Announcements; (3)All Multicast Capable
Intermediate Systems and (4)a group SNPA address corresponding to a
group Network address
6.5 Timers
Two additional timers are employed: (1)the Multicast Announcement
Timer (MAT) and (2)Multicast Address Mapping Timer (MAMT). Old
multicast announcement or multicast address mapping information shall
be discarded after the Holding Timer expires to ensure the correct
operation of the protocol.
6.5.1 Multicast Announcement Timer
The Multicast Announcement Timer is a local timer (i.e., maintained
independently by each End System, one timer per group Network
address) which assists in performing the Report Multicast
Announcement function. The timer determines how often an End System
reports its desire to receive multicast PDUs with that group Network
address as its destination address parameter. Considerations in
setting this timer are similar to those described for the
Configuration timer in the ES-IS specification.
6.5.2 Multicast Address Mapping Timer
The Multicast Address Mapping Timer is a local timer (i.e.,
maintained independently by an Intermediate System which is actively
participating with End Systems to transfer multicast PDUs) which
assists in performing the Report Multicast Address Mapping function.
The timer determines how often an Intermediate System, actively
participating with End Systems for the transfer of multicast PDUs,
reports the Multicast Address Mapping for a particular group Network
address. The shorter the Multicast Address Mapping Timer, the more
quickly End Systems on the subnetwork will become aware of the
correct address mapping which may change due to the Intermediate
System becoming available or unavailable. There is a trade off
between increased responsiveness and increased use of resources in
the subnetwork and in the End Systems.
6.6 Extensions to the current protocol functions
In order to support multicast transmissions the following optional
ES-IS protocol functions will be implemented:
6.6.1 Report Configuration by Intermediate Systems
All multicast capable Intermediate Systems on a subnetwork shall use
the Multicast Capable option in all ISH PDUs that they originate.
This will provide multicast capable End Systems with a way to
determine that a multicast capable Intermediate System is operating
on a particular subnetwork.
6.6.2 Query Configuration
Note: The Query Configuration function cannot be performed to find
the corresponding SNPA address of a group Network address since the
addressing information needed is the corresponding group SNPA address
and not the SNPA address of a particular End System responding. On a
large broadcast subnetwork, many different Configuration Responses
could result each incorporating a different End System Address. While
it is possible to design a Query Configuration for use with
multicast, this function does not appear to be required given the use
of the "All Multicast Capable End Systems" address for supplying a
SNPA address when the group SNPA address is not known.
6.7 Multicast Announcement
6.7.1 Report Multicast Announcement Function by End Systems
An End System which needs to receive or continue to receive any
multicast PDUs (i.e., PDUs with group Network addresses as their
destination address), constructs and transmits ESGH PDUs to inform
multicast capable Intermediate Systems of the set of group Network
address destinations for which it wishes to receive PDUs. This may be
done by constructing ESGH PDUs for each group Network address.
Alternatively, ESGH PDUs may be constructed which convey information
about more than one group Network address at a time, up to the limits
imposed by the permitted SNSDU size and the maximum header size of
the ESGH PDU. Each ESGH PDU is transmitted by issuing an SN-
UNITDATA.Request with the following parameters:
SN_Userdata (SNSDU) <- ESGH PDU
SN_Destination _Address <- multi-destination address that indicates
"All Multicast Announcements"
If an End System is attached to more than one subnetwork, the
information about each group Network address desired for receiving on
a particular subnetwork serving the End System shall be transmitted
via that subnetwork. It is permissible for an End System to report
group Network addresses on multiple subnetworks; however, duplicate
multicast PDUs should be anticipated.
The Group Address Pair parameter carries a list of Group Network
Addresses, each paired with its associated SNPA address. This
information is used by the Active Multicast IS to determine whether a
Multicast Address Mapping PDU should be emitted to update the
association between Group Network Addresses and SNPA addresses.
The Holding Time (HT) field is set to approximately twice the ES's
Multicast Announcement Timer (MAT) parameter. The value shall be
large enough so that even if every other ESGH PDU is discarded (due
to lack of resources), or otherwise lost in the subnetwork, the
multicast announcement information will still be maintained. The
value should be set small enough so that Intermediate Systems
resources are not needlessly consumed when the ES no longer wishes to
receive PDUs destined to a group Network address.
Note: When combining multiple group Network addresses in a single
ESGH PDU, it should be realized that there is a single Holding Time
parameter associated with all of these addresses.
6.7.1.1 Generating Jitter on Multicast Announcement Timers
The ES shall apply a 25% jitter to its Multicast Announcement Timer
(MAT) parameter. When ESGH PDUs are transmitted as a result of timer
expiration, there is a danger that the timers of individual systems
may become synchronised. The result of this is that the traffic
distribution will contain peaks. Where there are a large number of
synchronised systems, this can cause overloading of both the
transmission medium and the systems receiving the PDUs. In order to
prevent this from occurring, all periodic timers, the expiration of
which can cause the transmission of PDUs, shall have "jitter"
introduced as defined in the following algorithm.
CONSTANT
Jitter = 25;
Resolution = 100;
(* The timer resolution in ms *)
PROCEDURE Random(max: Integer): Integer;
(* This procedure delivers a Uniformly distributed random
integer R such that 0 < R <max *)
PROCEDURE WaitUntil(time: Integer)
(* This procedure waits the specified number of
ms and then returns *)
PROCEDURE CurrentTime(): Integer
(* This procedure returns the current time in ms *)
PROCEDURE
DefineJitteredTimer(baseTimeValueInSeconds : Integer;
expirationAction : Procedure);
VAR
baseTimeValue, maximumTimeModifier, waitTime : Integer;
nextexpiration : Time;
BEGIN
baseTimeValue := baseTimeValueInSeconds * 1000 / Resolution;
maximumTimeModifier := baseTimeValue * Jitter / 100;
(* Compute maximum possible jitter *)
WHILE running DO
BEGIN
(*First compute next expiration time *)
randomTimeModifier := Random(maximumTimeModifier);
waitTime:= baseTimeValue - randomTimeModifier;
nextexpiration := CurrentTime() + waitTime;
(* Then perform expiration Action *)
expirationAction;
WaitUntil(nextexpiration);
END (* of Loop *)
END (* of DefineJitteredTimer *)
Thus the call "DefineJitteredTimer(HelloTime, SendHelloPDU);" where
"HelloTime" is 10 seconds, will cause the action "SendHelloPDU" to be
performed at random intervals of between 7.5 and 10 seconds. The
essential point of this algorithm is that the value of
"randomTimeModifier" is randomised within the inner loop. Note that
the new expiration time is set immediately on expiration of the last
interval, rather than when the expiration action has been completed.
The time resolution shall be less than or equal to 100 ms. It is
recommended to be less than or equal to 10ms. The time resolution is
the maximum interval than can elapse without there being any change
in the value of the timer. The periodic transmission period shall be
random or pseudo-random in the specified range. with uniform
distribution across similar implementations.
Note: Applying jitter to the MAT parameter is required in order to
support the optional Damping function. If no jitter is applied on a
subnetwork where many ESs are requesting a particular multicast PDU
it is likely that they will have the same value for their MAT and
these timers may all become synchronised. Such synchronisation will
result in peaks in the distribution of traffic as described above.
The resulting overloading of the transmission medium and the systems
receiving the PDUs will negate any beneficial use of the Damping
function (since systems may be attempting to transmit their own ESGH
PDUs at the time they receive ESGH PDUs originated by other ESs with
the same group Network address.
6.7.2 Record Multicast Announcement Function
The Record Multicast Announcement function receives ESGH PDUs,
extracts the multicast announcement information and updates the
information in its routing information base.
The receiving system is not required to process any option fields in
a received ESGH PDU.
Note: When a system chooses to process these optional fields, the
precise actions are not specified by this International Standard.
6.7.2.1 Record Multicast Announcement Function by Intermediate Systems
On receipt of an ESGH PDU an IS with the optional multicast
capabilities extracts the configuration information and stores the
{group Network address, subnetwork} in its routing information base
replacing any other information for the same entry.
The Active Multicast IS upon receipt of an ESGH PDU also extracts the
Paired SNPA Address parameter corresponding to each group Network
address in the ESGH PDU. If the Active Multicast IS has a mapping for
a group Network address carried in the ESGH for which the paired SNPA
address does not match, the Report Multicast Address Mapping function
is performed.
6.7.2.2 Optional Damping Function
An ES with the optional capabilities to support multicast transfer
may decide to process ESGH PDUs multicast by other End Systems. There
is potentially some reduction in network traffic by doing this. An ES
requesting to receive multicast PDUs is permitted to reset its
Multicast Announcement Timer corresponding to one group Network
address on one subnetwork upon receiving an ESGH PDU from another ES
under the following circumstances:
a) The {group Network address, paired SNPA address} received on a
particular subnetwork matches that of the ES processing the ESGH
PDU for that subnetwork.
b) The Holding Timer parameter value in the ESGH PDU received is
equal to or greater than the Holding Timer value for the, group
Network address, being used by the ES processing this PDU.
6.7.3 Flush Old Multicast Announcement Function
The Flush Old Multicast Announcement function is executed to remove
multicast announcement entries in its routing information base whose
Holding Timer has expired. When the Holding Timer for a group Network
address expires, this function removes the corresponding entry from
the routing information base of the local IS for the corresponding
subnetwork.
6.8 Multicast Address Mapping
6.8.1 Report Multicast Address Mapping Function by Intermediate Systems
The Active Multicast Intermediate System constructs a MAM PDU,
corresponding to a group Network address for which it received via
the Record Multicast Announcement function, and issues these PDUs
under the following circumstances:
a) The IS initializes either as the Active Multicast IS after an
election with other multicast capable ISs or initializes after
determining it is the only multicast capable IS (the
determination of such conditions are outside of the scope of
this standard), or
b) The IS receives an ESGH PDU with a group Network address paired
to an SNPA address other than the SNPA address contained in the
Active Multicast IS's multicast address mapping information for
that group Network address, or
Note: The Active Multicast IS determines which mappings are correct.
Pre-configured mappings which are used prior to the initialization of
the Active Multicast IS may be determined to be incorrect by the
Active Multicast IS.
c) The expiration of the IS's Multicast Address Mapping Timer for
that group Network address.
Note: This is to prevent the expiration of Holding Timers in ESs.
d) The IS receives a multicast PDU originated on the subnetwork
which used an incorrect destination SNPA address.
Note: Of particular concern are those multicast packets using the
"All Multicast Capable Intermediate Systems" SNPA address when
another SNPA address should have been used. The Originating
Subnetwork Forwarding function is performed if this event occurs (see
section 6.11).
Note: The multicast capable ISs need to receive multicast packets on
all SNPA addresses that are contained in the current multicast
address mapping information for the subnetwork. The multicast
capable ISs are not required to receive multicast packets on any SNPA
addresses other than those contained in the current multicast address
mapping information and the "All Multicast Capable Intermediate
Systems" SNPA address.
Circumstances b) and d) are the event driven conditions for the
Active Multicast IS to construct and issue a MAM PDU. The Active
Multicast IS shall limit the number of MAM PDUs issued per unit of
time. MAM PDUs with identical information shall not be issued more
than once per second. Event conditions occurring 10 seconds after
the last issue of an appropriate MAM PDU shall result in the issuance
of another such MAM PDU.
The IS serving as the Active Multicast Intermediate System may
construct a MAM PDU for each group Network address. Alternatively,
MAM PDUs may be constructed which convey information about more than
one group Network address at a time, up to the limits imposed by the
permitted SNSDU size and the maximum header size of the MAM PDU. The
IS performs all multicast address mapping functions independently for
each of its subnetworks even if this IS is the Active Multicast IS on
multiple subnetworks. Each MAM PDU is transmitted by issuing an SN-
UNITDATA.Request with the following parameters:
SN_Userdata (SNSDU) <- MAM PDU
SN_Destination _Address <- multi-destination address that indicates
"All Multicast Capable End Systems"
The Holding Time (HT) field is set to approximately twice the
Intermediate System's Multicast Address Mapping Timer (MAMT)
parameter. This variable shall be set to a value large enough so
that even if every other MAM PDU, for a particular group Network
address, is discarded (due to lack of resources), or otherwise lost
in the subnetwork, the multicast address mapping information will
still be maintained. The value should be set small enough so that End
Systems will quickly cease to use the multicast address mappings
supplied by ISs that have failed.
Note: -- The Holding Timer parameter value applies to all group
Network addresses called out in the MAM PDU.
The Group Address Pair parameter is used to convey the association
between Group Network Addresses and SNPA addresses.
Optionally, the Active Multicast IS may include information in the
MAM PDU indicating a larger population of group Network addresses to
which the same multicast address mapping information applies. There
are two optional fields for this purpose: the Group Network Address
Mask option and the Paired SNPA Address Mask option.
There are three permitted cases for including or excluding the masks.
In the first case, both masks are absent. In this case the MAM PDU
conveys information about one set of enumerated group Network
addresses only.
Note: -- Multiple group address pairs may be contained in a single
MAM PDU.
In the second case, the MAM PDU contains a Group Network Address Mask
but no Paired SNPA Address Mask. In this case, the MAM PDU conveys
information about an equivalence class of group Network addresses.
The information reveals that multiple group Network addresses are
mapped to the same SNPA address.
In the third case, the MAM PDU contains both masks. As in the second
case, the MAM PDU conveys information about an equivalence class of
group Network addresses. But in this case, the information reveals
that the SNPA addresses for the equivalence class of group Network
address are embedded in the group Network address. In particular the
Paired SNPA Address Mask indicates the location of the SNPA address
in the group Network Address(es).
The Active Multicast IS shall construct a MAM PDU with direct
information, not needing analysis of the Mask parameters, in response
to the occurrence of an event driven condition. The Active Multicast
IS may provide additional information in such a MAM PDU via the use
of Mask parameters.
An IS may suggest a value for End Systems on the local subnetwork to
use as their Multicast Announcement Timers, for a specific group
Network address, by including the Suggested ES Multicast Announcement
Timer (ESMAT) parameter in the transmitted MAM PDU. Setting this
parameter permits the Active Multicast IS to influence the frequency
with which ESs transmit ESGH PDUs.
Note: If the ESMAT parameter is used, the one value permitted in the
MAM PDU is suggested for all group Network addresses called out in
the MAM PDU.
6.8.2 Record Multicast Address Mapping Function by End Systems
The Record Multicast Address Mapping function receives MAM PDUs,
extracts the multicast address mapping information and updates the
information in its routing information base. The receiving system is
not required to process any option fields in a received MAM PDU with
the exception of the Suggested ES Multicast Announcement Timer
(ESMAT) parameter.
Note: When a system chooses to process these optional fields, the
precise actions are not specified by this International Standard.
On receipt of a MAM PDU an ES with the optional multicast
capabilities extracts the multicast address mapping information and
stores the {group Network address, paired SNPA address} for a
particular subnetwork in its routing information base replacing any
other information for the same group Network address and subnetwork.
In addition, an ES shall set its Multicast Announcement Timer,
corresponding to the group Network address for which it is performing
the Record Multicast Address Mapping function, based on receipt of a
MAM PDU, corresponding to that group Network address, containing an
ESMAT parameter.
Note: While an ES may process ESGH PDUs multicast by other ESs to
support the optional Damping function, an ES is not permitted to
change its own mapping due to the mapping found in other ES's ESGH
PDUs.
6.8.3 Flush Old Multicast Address Mapping Function by End Systems
The Flush Old Multicast Address Mapping function is executed to
remove multicast address mapping entries in its routing information
base whose corresponding Holding Timer has expired. When such a
Holding Timer for a multicast address mapping expires, this function
removes the corresponding entry from its routing information base for
the corresponding SNPA.
6.9 Paired SNPA Address Selection Function by End Systems
An End System shall pair each group Network address with an
associated SNPA address to support receiving (e.g., performing the
Report Multicast Announcement function) and originating multicast
PDUs.
6.9.1 Paired SNPA Address Selection for Receiving Multicast PDUs
An End System always has a paired SNPA address for every active group
Network address on a particular subnetwork. This mapping is obtained
by:
a) recording a multicast address mapping which is maintaining an
active holding timer, or if there has been no dynamic
information received, by
b) having pre-configured multicast address mapping information, or
if neither dynamic nor pre-configured information is available,
by
c) mapping the "All Multicast Capable End Systems" multi-
destination address to the group Network address.
6.9.2 Paired SNPA Address Selection for Originating Multicast PDUs
An End System, originating a multicast PDU, pairs a SNPA address to
the group Network address. This mapping is obtained in the following
manner:
a) If there is a multicast capable IS reachable on the subnetwork
then the SNPA address used by an End System originating a multi-
cast PDU is either the paired SNPA address obtained from the
multicast address mapping information associated with the group
Network address in the multicast PDU's Destination address
parameter or if there is no valid entry for the group Network
address by using the "All Multicast Capable Intermediate Sys-
tems" multi-destination address, or if there is no multicast
capable Intermediate System on the subnetwork, by
Note: Multicast address mapping information is valid if the Holding
Timer associated with it has not expired.
Note: An ES can determine if a multicast capable IS is reachable on
the subnetwork by having for that subnetwork either (1)multicast
address mapping information or (2)routing information received via an
ISH PDU containing a Multicast Capable optional parameter. In either
case the information must be valid (i.e., the Holding Timer for the
information must not have expired).
b) having pre-configured multicast address mapping information, or
if neither a multicast capable Intermediate System is present on
the subnetwork nor pre-configured information is available, by
c) mapping the "All Multicast Capable End Systems" multi-
destination address to the group Network address.
6.10 Extensions to the ISO CLNP Route Function by End Systems
An End System attached to more than one subnetwork shall determine
when originating a multicast PDU whether to forward this multicast
PDU to more than one subnetwork or not. End Systems shall originate
each multicast PDU on all subnetworks for which the ISO ES-IS
Configuration function is actively reporting the NSAP address
contained in the Source Address parameter of the multicast PDU. As a
result of this function multiple invocations of the ISO CLNP
Forwarding function may result when such an ES originates a multicast
PDU.
6.11 Originating Subnetwork Forwarding Function by Intermediate
Systems
The Active Multicast IS upon receiving a multicast PDU originated on
a subnetwork which used the "All Multicast Capable Intermediate
Systems" SNPA address when another SNPA address should have been
used, performs the Originating Subnetwork Forwarding function. The
multicast address mapping information defines the correct SNPA
address pairings for a given subnetwork. The Originating Subnetwork
Forwarding function forwards the multicast PDU back on subnetwork it
was originated on. In the case that the ES was attached to more than
one subnetwork and originated the multicast PDU on more than one
subnetwork, the Active Multicast IS for each subnetwork performs the
Originating Subnetwork Forwarding function for the subnetwork that
they are responsible for.
The Active Multicast IS obtains the contents for the multicast PDU
for the Originating Subnetwork Forwarding function by using the
contents of the multicast PDU received with the incorrect destination
SNPA address and replacing the original PDU Lifetime field with the
value one (0000 0001). The Active Multicast IS performs the ISO 8473
PDU Composition function and forwards the PDU to the subnetwork that
the PDU was originated on using the ISO 8473 Forwarding function with
the correct destination SNPA address.
Note: The PDU Lifetime field is set to "one" to ensure that ISs
attached to the originating subnetwork do not forward this PDU on.
Such ISs should have received the PDU when it was originated since
this function is only performed in the event of receiving a multicast
PDU incorrectly addressed to the "All Multicast Capable Intermediate
Systems" SNPA address.
6.12 Structure and Encoding of PDUs
The ES-IS multicast control functions are supported via the exchange
of ESGH and MAM PDUs. The one exception to this is that a new
optional parameter, the Multicast Capable parameter, is provided for
use within the ISH PDU.
6.12.1 PDU Type Codes
The Multicast Announcement is accomplished via the transfer of End
System Group Hello (ESGH) PDUs. The PDU type code for an ESGH PDU is
"0 0 1 0 1". The Multicast Address Mapping (MAM) is accomplished via
the transfer of Multicast Address Mapping PDUs. The PDU type code for
a MAM PDU is "0 0 1 1 1".
6.12.2 Hold Time field
The Holding Time field specifies the maximum time for the receiving
Network entity to retain the multicast announcement or multicast
address mapping information contained in the PDU.
6.12.3 Structure of Addressing Parameters
The ESGH and MAM PDUs carry one or more group Network addresses
(GNAs) each with their associated Paired SNPA Address (PSA).
6.12.4 Group Address Pair Parameter for ESGH and MAM PDUs
The Group Address Pair parameter is a list of one or more group
Network addresses each with their associated Paired SNPA address. The
group Network address identifies specific multicast PDUs and the
Paired SNPA address is the SNPA address on which the ES expects to
receive such multicast PDUs on that subnetwork. It is encoded in the
ESGH and MAM PDUs as shown in Figure 1.
Octet
,----------------------------------------------------,
Number of Group Address Pairs 10
----------------------------------------------------
Group Network Address Length Indicator (GNAL) 11
----------------------------------------------------
12
: Group Network Address (GNA) :
----------------------------------------------------
Paired SNPA Address Length Indicator (PSAL)
----------------------------------------------------
: Paired SNPA Address (PSA) :
----------------------------------------------------
GNAL
----------------------------------------------------
: GNA :
----------------------------------------------------
PSAL
----------------------------------------------------
: PSA :
m-1
'----------------------------------------------------'
Figure 1 - ESGH and MAM PDUs - - Group Address Pair Parameter
6.12.5 Extensions to the current Option Parameters
The Security and Priority optional parameters may be carried in a
ESGH PDU. There is no Security or Priority option for the MAM PDU.
6.12.6 Suggested ES Multicast Announcement Timer
The ESMAT parameter may appear only in the MAM PDU
The ESMAT parameter conveys the value that an IS requests the
receiving ESs to use as their local Multicast Announcement Timer.
Parameter Code: 1100 0111
Parameter Length: two octets
Parameter Value: ESMAT in units of seconds.
6.12.7 Multicast Capable
The Multicast Capable option may appear only in the ISH PDU
The Multicast Capable options consists only of a one octet code and a
one octet parameter length field, there is no parameter field.
Parameter Code: 1100 1000
Parameter Length: zero octets
Parameter Value: none (parameter does not exist).
6.12.8 Group Network Address Mask
The Group Network Address Mask option may only appear in the MAM PDU.
The Group Network Address Mask parameter indicates that the multicast
address mapping information applies to a larger population of group
Network Addresses than the group Network address(es) contained in the
MAM PDU indicates. When this option is provided in a MAM PDU, the
maSKINg relationship contained must be valid for all group Network
addresses contained in this PDU. An End System may ignore this
parameter.
The Group Network Address Mask establishes an equivalence class of
group Network addresses to which the same multicast address mapping
information applies. To determine whether or not a trial group
Network address falls within the equivalence class, the ES aligns the
trial group Network address with the Group Network Address Mask
padding the latter with trailing zero octets if necessary. If in all
bit positions where the Group Network Address Mask is "1" the trial
group Network address matches the Group Network Address field of the
Group Address Pair parameter of the MAM PDU, then the trial group
Network address belongs to the equivalence class described by the MAM
PDU.
The Group Network Address Mask parameter has additional semantics
when considered with the Paired SNPA Address Mask parameter.
Parameter Code: 1110 0011
Parameter Length: variable, up to 20 octets
Parameter Value: a comparison mask of octets to be
aligned with the Group Network Address
field of the Group Address Pair
parameter of the MAM PDU.
6.12.9 Paired SNPA Address Mask
The Paired SNPA Address Mask option may only appear in the MAM PDU.
When the Paired SNPA Address Mask is present, the equivalence class
defined by the Group Network Address Mask also has common structure
below the Group Network Address Mask; i.e., in the portion of the
group Network address where the Group Network Address Mask is
logically "0". The Paired SNPA Address Mask supplies additional
information about the structure, by indicating certain bit positions
within the space "below" the Group Network Address Mask.
Specifically, the Paired SNPA Address Mask indicates the location of
the Paired SNPA address in the Group Network Address.
This parameter may appear in a MAM PDU only if the Group Network
Address Mask is also present. When this option is provided in a MAM
PDU, the masking relationship contained must be valid for all group
Network addresses contained in this PDU. An ES receiving such a MAM
PDU may safely ignore both masks. However (since presence of both
masks dictates different functional behavior than the presence of the
Group Network Address Mask alone) an ES shall not ignore one of the
masks while heeding the other.
Parameter Code: 1110 0100
Parameter Length: variable
Parameter Value: a comparison mask of octets to be
aligned with the Group Network Address
field(s) of the Group Address Pair
parameter of the MAM PDU.
6.12.9.1 Mask Parameters Example
This section provides examples of using the Group Network Address
Mask and the Paired SNPA Address Mask. The examples given are for an
Internet usage of CLNP Multicasting across subnetworks using IEEE 802
addressing. For these examples the group Network address format is:
+-----+----------------------------------------+
IDP Upper DSP Embedded SNPA address SEL
+-----+-----------+-----------------------+----+
octets: 3 10 6 1
+-----+-----------+-----------------------+----+
Thus the group Network address used is 20 octets. For these
examples, the only field considered is the Embedded SNPA address
field and its placement within the group Network address.
In the first example it is the policy in "this part of the Internet"
to map the Embedded SNPA address into the IEEE 802 address space
reserved by IEEE 802 for group addressing using LOCAL assignment,
this corresponds to all 48 bit values with the two low order bits of
the first octet set to "11".
The Active Multicast Intermediate System on this subnetwork may
construct a MAM PDU to map, for this example, a group Network address
of {13 octets, 03-00-DA-DA-DA-DA, 1 octet} and a paired SNPA address
of 03-00-DA-DA-DA-DA. In addition the Active Multicast Intermediate
System can include in the MAM PDU a Group Network Address Mask of
FF-FF-FF-FF-FF-FF-FF-FF-FF-FF-FF-FF-FF-03-00-00-00-00-00-00.
With this parameter, all group Network addresses which share the
identical first 13 octet and with "11" in the two low order bits of
the 14th octet are put in an equivalence class and share the same
mapping information. If this were the only option present then all of
these group Network addresses would all have a paired SNPA address of
03-00-DA-DA-DA-DA.
In order to map the group Network addresses to the range of IEEE
addresses of this example, the MAM PDU must also contain a Paired
SNPA Address Mask. The Paired SNPA Address Mask identifies where the
SNPA Address is contained within the group Network addresses (defined
by the equivalence class formed by the Group Network Address Mask
within the same PDU). For this example the Paired SNPA Address Mask
is 00-00-00-00-00-00-00-00-00-00-00-00-00-FF-FF-FF-FF-FF-FF-00.
As a second example, all group Network addresses with a specific OUI
(organizationally unique identifier) using the twenty octet group
Network address format provided above are mapped to their embedded
SNPA address. An OUI is assigned by IEEE 802 and is three octets in
length. The OUI is contained in the first three address octets of a
GLOBALLY assigned IEEE 802 address. For this example the MAM PDU
must contain the following:
1. A group Network address contained within the MAM PDU with the
OUI of interest.
2. A group Network address Mask of FF-FF-FF-FF-FF-FF-FF-FF-FF-
FF-FF-FF-FF-FF-FF-FF-00-00-00-00.
3. A Paired SNPA Address of 00-00-00-00-00-00-00-00-00-
00-00-00-00-FF-FF-FF-FF-FF-FF-00.
6.12.10 End System Group Hello (ESGH) PDU
The ESGH PDU has the format shown in figure 2:
Octet
,----------------------------------------------------,
Network Layer Protocol Identifier 1
----------------------------------------------------
Length Indicator 2
----------------------------------------------------
Version/Protocol ID Extension 3
----------------------------------------------------
reserved (must be zero) 4
----------------------------------------------------
0 0 0 Type (00101 = ESGH) 2
----------------------------------------------------
Holding Time 6,7
----------------------------------------------------
Checksum 8,9
----------------------------------------------------
Number of Group Address Pairs 10
----------------------------------------------------
Group Network Address Length Indicator (GNAL) 11
----------------------------------------------------
12
: Group Network Address (GNA) :
----------------------------------------------------
Paired SNPA Address Length Indicator (PSAL)
----------------------------------------------------
: Paired SNPA Address (PSA) :
----------------------------------------------------
GNAL
----------------------------------------------------
: GNA
----------------------------------------------------
PSAL
----------------------------------------------------
: PSA :
m-1
----------------------------------------------------
m
: Options :
p-1
'----------------------------------------------------'
Figure 2 - ESGH PDU Format
6.12.11 Multicast Address Mapping (MAM) PDU
The MAM PDU has the format shown in figure 3:
Octet
,----------------------------------------------------,
Network Layer Protocol Identifier 1
----------------------------------------------------
Length Indicator 2
----------------------------------------------------
Version/Protocol ID Extension 3
----------------------------------------------------
reserved (must be zero) 4
----------------------------------------------------
0 0 0 Type (00111 = MAM) 2
----------------------------------------------------
Holding Time 6,7
----------------------------------------------------
Checksum 8,9
----------------------------------------------------
Number of Group Address Pairs 10
----------------------------------------------------
Group Network Address Length Indicator (GNAL) 11
----------------------------------------------------
12
: Group Network Address (GNA) :
----------------------------------------------------
Paired SNPA Address Length Indicator (PSAL)
----------------------------------------------------
: Paired SNPA Address (PSA) :
----------------------------------------------------
GNAL
----------------------------------------------------
: GNA :
----------------------------------------------------
PSAL
----------------------------------------------------
: PSA :
m-1
----------------------------------------------------
m
: Options :
p-1
'----------------------------------------------------'
Figure 3 - MAM PDU Format
6.13 Conformance
All of the extensions provided to the functions to support multicast
capability are optional. For an End System or Intermediate System
which is not multicast capable these extensions are not applicable. A
Network entity may choose to be multicast capable, a multicast
capable Network entity is required to support both multicast
announcement information and multicast address mapping information.
An implementation claiming conformance as a multicast capable End
System shall meet all of the requirements for an End System which is
not multicast capable and shall support multicast announcement
information and shall implement the functions marked as Mandatory (M)
in column 4 of table 3. A multicast capable End System implementation
shall also support multicast address mapping information and shall
implement the functions marked as Mandatory (M) in column 5 of table
3.
An implementation claiming conformance as a multicast capable
Intermediate System shall meet all of the requirements for an
Intermediate System which is not multicast capable and shall support
multicast announcement information and shall implement the functions
marked as Mandatory (M) in column 6 of table 3. A multicast capable
Intermediate System implementation shall also support multicast
address mapping information and shall implement the functions marked
as Mandatory (M) in column 7 of table 3.
Table 3 - Static Conformance Requirements for Multicast Capable
Network Entities
ES IS
Clause --------------
Label Function Reference AI MI AI MI
------------------------------------------------------------------
RpMAn Report Multicast Announcement 6.7.1 M - - -
RcMAn Record Multicast Announcement 6.7.2.1 - - M -
RcDamp Record Damping 6.7.2.2 O - - -
FlMAn Flush Old Multicast Announcement 6.7.3 O - M -
RpMAdMa Report Multicast Address Mapping 6.8.1 - - - M
MATGn ESMAT Generation 6.8.1 - - - M
RcMAdMa Record Multicast Address Mapping 6.8.2 - M - -
MATPr ESMAT Processing 6.8.2 - M - -
FlMAdMa Flush Old Multicast Address Map 6.8.3 - M - -
PSAdSel Paired SNPA Address Selection 6.9.1 - M - -
ExtForw Extensions to CLNP Route Function 6.10 - M - -
OSuForw Originating Subnetwork Forwarding 6.11 - - - M
Key:
AI = Multicast Announcement information supported
MI = Multicast Address Mapping information supported
M = Mandatory; O = Optional; - = not applicable
7. Security Considerations
Security issues are not discussed in this memo.
Appendix A. Differences with RFC1112
This appendix is intended to identify differences between the
mechanisms defined for CLNP Multicast in this specification and those
for IP multicast defined in RFC1112. The work on CLNP Multicast
followed the work on IP multicast and was explicitly aimed at
bringing the capabilities described in RFC1112 into a CLNP context.
This appendix is intended to provide some background information on
the difference; however, it is not intended to justify the mechanisms
selected for CLNP multicast use.
Static/Dynamic Address Binding of Multicast Datagrams
IP multicast utilizes a static binding of Class D IP addresses to a
specific range of IEEE 802 48 bit group addresses. The IEEE 802
address range that is used is within the address range that IEEE 802
allocates for "Global" administration and this block of addresses is
under the control of the Internet Assigned Numbers Authority (IANA)
which in turn has allocated this block of addresses for use by IP
multicast. This scheme is very simple and efficient. Given the use
of a 32 bit IP address, the lower 23 bits of the Class D address are
mapped into the lower 23 bits of a 48 bit IEEE 802 address where the
upper 25 bits are fixed. Static binding of this form is global in
scope (all members of a group use the same IEEE 802 address on all
subnets (at least all that use IEEE 802 addressing).
CLNP multicast uses a dynamic binding of a group Network address (up
to 20 bytes) to any subnetwork address. In cases where no multicast
capable Intermediate Systems are attached to a subnetwork then a
binding using preconfigured information or the "All Multicast Capable
End Systems" subnetwork addresses is used. The large GNA provides the
room to contain a full 48 bit IEEE 802 address if desired. Mask
capabilities are optionally provided which allow a multicast capable
Intermediate System to specify a "static" binding for a particular
subnetwork. One of the major purposes of providing a dynamic binding
is to customize a host's subnetwork address usage to the capabilities
of the attached systems. There is considerable differences in the
numbers of group subnetwork addresses that a system can recognize
using hardware hooks built into the integrated circuits used. For
example the number of addresses that can be recognized by hardware
may differ by an attached system depending upon the interface it uses
(e.g., Ethernet interface and FDDI within the same system may have
quite different capabilities). Dynamic binding of this form is local
in scope (members of a group may use different subnetwork addresses
(e.g., IEEE 802 addresses) on different subnets).
Originating of Multicast Datagrams
IP multicast originates multicast datagrams directly, where the host
originating a datagram sends it with the group Subnetwork address as
its destination. Hosts attached to the network where the datagram is
originated receive the datagram directly.
CLNP multicast originates multicast datagrams directly using the
group's subnetwork address as its destination when multicast address
mapping information is available. This case occurs when a multicast
capable Intermediate System is attached to the subnetwork and a host
on the subnetwork is announcing an interest in multicast packets
identified by a particular group Network address. The Active
Multicast IS may use MAM PDU mask parameters to provide multicast
address mapping information for a large number of group Network
addresses. When there is no multicast address mapping information for
the particular group Network address on a subnetwork with a multicast
capable IS attached to it, hosts originate packets using such
addresses sends to the "All Multicast Capable Intermediate Systems"
SNPA address. This case occurs when there are no receivers of such
multicast packets on the originating subnetwork. When a multicast
capable Intermediate System is not attached to a subnetwork, the End
System may utilize either preconfigured information (which might be a
direct mapping from a portion of the group Network address) or use
the "All Multicast Capable End Systems" address.
Address Binding of Control Packets
IP multicast sends the control packets related to the IGMP protocol
on the same subnetwork address that is used by the multicast data
traffic.
CLNP multicast sends the control packets related to the ES-IS
protocol extensions on specific group subnetwork addresses (i.e.,
"All Multicast Capable End Systems" and "All Multicast Announcements"
addresses).
Router Requirements for relaying Multicast Datagrams
IP multicast requires that a multicast router run in "promiscuous"
mode where it must receive all multicast datagrams originated on a
subnetwork regardless of the destination. This is a result of the
choices selected in the "Originating of Multicast Datagrams" and
"Address Binding of Control Packets" discussed above.
CLNP multicast allows a multicast router to limit multicast packet
reception to only those datagrams sent to the SNPA addresses where
there is current multicast address mapping information or to the "All
Multicast Capable Intermediate Systems" address. The intention is to
allow the multicast routers to be in control of the SNPA addresses
for multicast packets that they need to receive. This is a result of
the choices selected in the "Originating of Multicast Datagrams" and
"Address Binding of Control Packets" discussed above.
Aggregation of Control Information
In IP multicast, a host is required to withhold an announcement
report upon hearing another host reporting a similar interest in a
particular Class D address on a particular subnetwork. This is an
option for CLNP multicast (upon hearing interest in a particular
group Network address on a particular subnetwork). Such reports are
not combined in IP multicast while CLNP multicast supports providing
multiple announcements (and address mappings) within a single packet.
A mask feature for address mappings supports identifying mappings for
a range of group Network addresses within a single control packet.
Datagram Scope Control
IP multicast supports the use of the IP Hop Count as a means to
support scope control. While not documented in RFC1112, a technique
is also being used to use bits within the Class D address to identify
whether a datagram has single subnetwork, "campus" or global scope.
CLNP has considerable scope control functionality. While the PDU
Lifetime field can be employed in a similar way to the IP Hop Count,
two additional options are available. The Radius scope control
provides a mechanism for "administratively" setting distance values
and de-couples the multicast scope control from the PDU lifetime
function. More importantly, the Prefix based scope control appears to
provide considerable and flexible functionality that can adjust to
situations where a known, hierarchical unicast addressing structure
exists.
Marking of Multicast Datagrams
IP multicast marks a multicast PDU via the use of an IP Class D
address as its destination address parameter. CLNP multicast marks
both the PDU (a different PDU type) and the destination address
(i.e., group Network address) parameter.
Unicast Addressing Differences
An IP address identifies a specific host interface while a CLNP
individual Network address (i.e., NSAP address) identifies a
particular Network entity. This difference has lead to a difference
with RFC1112. IP multicast requires a host which is attached to
more than one subnetwork to originate a multicast packet on only one
subnetwork. CLNP multicast requires a host which is attached to more
than one subnetwork to originate a multicast packet on every
subnetwork that the ISO ES-IS Configuration function is reporting the
NSAP address contained in the source address parameter of the
multicast PDU.
Error Reports
Error reports sent in response to receiving a multicast PDU are not
permitted in IP multicast while they are permitted in CLNP multicast.
Source Routing
Source routing of multicast PDUs are permitted in IP multicast (but
at the present time this is discouraged) while they are not permitted
in CLNP multicast.
Appendix B. Issues Under Study
This appendix is intended to record the current issues (as discussed
at the March 1994 TUBA meeting).
1. Local versus Global address bindings
The extensions to the ES-IS protocol provide a multicast address
mapping function which supports dynamically binding a group Network
address to a subnetwork address. Concern has been expressed that
this is an unnecessary feature which complicates the job of network
administrators without suitable benefit. A static, global binding of
group Network addresses to IEEE 802 subnetwork addresses, as is used
by IP multicast has been suggested.
The two main reasons that the group Network address to subnetwork
(IEEE 802) address was made locally configurable were to support
multicast on subnets with hosts having a mixture of capabilities (as
to how many multicast subnetwork addresses a host could register to
receive at a time) and to support multicast on subnets that do not
use 48 bit IEEE 802 addresses. Thus it was felt that this should be
done per subnetwork versus globally. Even multi-homed hosts with
subnets that use 802 addresses may have varying capabilities (looking
at typical Ethernet, FDDI and 802.5 implementations).
One possible solution is to recommend a direct mapping in any
Internet use of CLNP multicast on subnets which use IEEE 802
addressing. This could be a default for all Internet hosts. A
policy would be needed to identify the Internet's group Network
address format. Given such a mapping the only operational overhead
that would occur is that in the presence of a mapping server (the
Active Multicast IS), which was supporting this mapping, a MAM PDU
would periodically be sent with a Group Network Address Mask which
would identify the direct mapping.
2. "Real Time" Scope Control Features
The scope control features are provided via optional parameters. Use
of multicast transfer of audio and video streams may require scope
control mechanisms which operate very quickly.
One possible solution is to embed scope control mechanisms into the
group Network address itself. For example, a group Network address
using the "Local" AFI is automatically limited to not cross inter-
domain borders. Further, more flexible, address formats may be
developed.
References
[Deering91] Deering, S., "Multicast Routing in a Datagram
Internetwork", PhD thesis, Electrical Engineering Dept., Stanford
University, December 1991.
[RFC1112] Deering, S., "Host Extensions for IP Multicasting",
STD 5, RFC1112, Stanford University, August 1989.
[RFC1237] Colella, R., Gardner, E., and R. Callon, "Guidelines for OSI
NSAP Allocation in the Internet", RFC1237, NIST, Mitre, DEC, July
1991.
[CLNP] Protocol for providing the connectionless-mode network service,
International Standard 8473-1, Second Edition, ISO/IEC JTC 1,
Switzerland 1994. (Available via FTP from
merit.edu:pub/iso/iso8473part1.ps).
[ES-IS] End system to Intermediate system routing exchange protocol
for use in conjunction with the Protocol for providing the
connectionless-mode network service, International Standard 9542,
ISO/IEC JTC 1, Switzerland 1987. (Available via FTP from
merit.edu:pub/iso/iso9542.ps).
[MULT-AMDS]: Amendments to ISO standards to support CLNP multicast
extensions:
ISO 8348 AM5 Amendment to the Network Service to support Group Network
Addressing. International Standard ISO 8348 Amendment 5, ISO/IEC JTC
1, Switzerland 1994.
ISO 8473-1 DAM1 - Draft Amendment to the Second Edition of the
Protocol for providing the connectionless-mode network service [CLNP],
Multicast Extension, 1993.
ISO 9542 DAM2 - Draft Amendment to the ES-IS [ES-IS] protocol,
Addition of connectionless- mode multicast capability, 1993.
Author's Address
Dave Marlow
Code B35
NSWC-DD
Dahlgren, VA. 22448
Phone: (703) 663-1675
