昨天在为一台Cisco 3640升级IOS，并加装了三个NM模块（一个NM-2FE2W；一个NM-2CE1U；一个NM-2V并加装两个VIC-2FXO）
现将升级3640时的CRT显示贴出来，让大家看看是什么问题导致的启动失败。
ID MEMORY_REQ TYPE
00003B 0X001AA000 Two CE1 - Unbalanced (75 Ohm - Coax)
000065 0X0002E500 Four port Voice PM
0000D8 0X00178610 Dual Fast Ethernet Combo Port Module, 2 WAN
0X000F3BB0 public buffer pools
0X00211000 public particle pools
TOTAL: 0X006556C0
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 7Mb.
Using 10 percent iomem. [7Mb/64Mb]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3640-IS-M), Version 12.2(8)T4, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Fri 03-May-02 16:58 by ccai
Image text-base: 0x60008930, data-base: 0x61558000
%ERR-1-GT64010: Fatal error, Parity error on master read
cause=0x0110E083, mask=0x0CD01F00, real_cause=0x00100000
bus_err_high=0x00000000, bus_err_low=0x31000000, addr_decode_err=0x14000470
r0 = FFFFFFFF r1 = FFFFFFFF r2 = 0 r3 = 62320000 r4 = 0
r5 = 4 r6 = 0 r7 = 14AA9148 r8 = 0 r9 = 0
r10 = 0 r11 = 0 r12 = 0 r13 = 14 r14 = 0
r15 = F4240 r16 = 0 r17 = 1 r18 = 0 r19 = 0
r20 = 0 r21 = 3401C100 r22 = FFFFFFFF r23 = FFFF00FF r24 = 0
r25 = 6044BE58 r26 = 0 r27 = 2B5 r28 = 0 r29 = 20000000
r30 = 0 r31 = 0 r32 = FFFFFFFF r33 = FFFFFFFF r34 = FFFFFFFF
r35 = FFFFFFFF r36 = FFFFFFFF r37 = FFFFFFFF r38 = FFFFFFFF r39 = FFFFFFFF
r40 = FFFFFFFF r41 = FFFFFFFF r42 = FFFFFFFF r43 = FFFFFFFF r44 = FFFFFFFF
r45 = FFFFFFFF r46 = FFFFFFFF r47 = FFFFFFFF r48 = 0 r49 = 627F7414
r50 = 0 r51 = 2 r52 = 0 r53 = 3041F001 r54 = 0
r55 = 30410000 r56 = FFFFFFFF r57 = FFFFFFFF r58 = 0 r59 = 626EEBE0
r60 = FFFFFFFF r61 = FFFFFFFF r62 = 0 r63 = 60FBC8D8
sreg = 3401E103 mdlo_hi = 0 mdlo = 9C4
mdhi_hi = 0 mdhi = 0 badvaddr_hi = FFFFFFFF
badvaddr = FFFFFFFF cause = FFFFFFFF epc_hi = 0
epc = 60FBC200 err_epc_hi = FFFFFFFF err_epc = FFFFFFFF
%ERR-1-FATAL: Fatal error interrupt, reloading
err_stat=0x10
=== Flushing messages (00:00:07 UTC Mon Mar 1 1993) ===
Queued messages:
No fault history 0xFFFFFFFF. Need 11.1 (2) or
higher ROM
SYSTEM INIT: INSUFFICIENT MEMORY TO BOOT THE IMAGE!
System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
C3600 processor with 65536 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled
monitor: command "boot" aborted due to user interrupt
rommon 1
rommon 1 ?
alias set and display aliases command
boot boot up an external process
break set/show/clear the breakpoint
confreg configuration register utility
cont continue executing a downloaded image
context display the context of a loaded image
cookie display contents of cookie PROM in hex
dev list the device table
dir list files in file system
dis disassemble instruction stream
dnld serial download a program module
frame print out a selected stack frame
help monitor builtin command help
history monitor command history
meminfo main memory information
repeat repeat a monitor command
reset system reset
set display the monitor variables
stack produce a stack trace
sync write monitor environment to NVRAM
sysret print out info from last system return
unalias unset an alias
unset unset a monitor variable
xmodem x/ymodem image download
rommon 2 xmodem ?
Do not start the sending program yet...
File size Checksum File name
4096 bytes (0x1000) 0x0000 c3640-is-mz.122-8.T4.bin (deleted) (bad checksum: 0x9111)
14404760 bytes (0xdbcc98) 0x52d5 c3640-is-mz.122-8.T4.bin
WARNING: All existing data in flash will be lost!
Invoke this application only for disaster recovery.
Do you wish to continue? y/n [n]: y
Do you wish to continue? y/n [n]: y
Ready to receive file ? ...
Erasing flash at 0x30fc0000
program flash location 0x304c0000
Download Complete!
program load complete, entry point: 0x80008000, size: 0x4c274c
Self decompressing the image : ################################################################################################################################################################################################################################################################################################################################################################################################################# [OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3640-I-M), Version 12.0(7)XK2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC:Home:SW:IOS:Specials for info
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Tue 31-Oct-00 20:56 by kpma
Image text-base: 0x600088F0, data-base: 0x608C2000
cisco 3640 (R4700) processor (revision 0x00) with 58368K/7168K bytes of memory.
Processor board ID 29401660
R4700 CPU at 100Mhz, Implementation 33, Rev 1.0
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
Primary Rate ISDN software, Version 1.1.
2 FastEthernet/IEEE 802.3 interface(s)
2 Channelized E1/PRI port(s)
DRAM configuration is 64 bits wide with parity disabled.
125K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
ip pim bidir-enable
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
00:00:04: %PA-2-UNDEFPA: Undefined Port Adaptor type 101 in bay 2
Router
00:00:08: %SYS-4-CONFIG_NEWER: Configuration from version 12.2 may not be correctly understood
00:00:08: %SYS-5-CONFIG_I: Configured from memory by console
00:0
