Network Working Group F. Baker
Request For Comments: 1638 ACC
Category: Standards Track R. Bowen
IBM
Editors
June 1994
PPP Bridging Control Protocol (BCP)
Status of this Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Abstract
The Point-to-Point Protocol (PPP) [6] provides a standard method for
transporting multi-protocol datagrams over point-to-point links. PPP
defines an extensible Link Control Protocol, and proposes a family of
Network Control Protocols for establishing and configuring different
network-layer protocols.
This document defines the Network Control Protocol for establishing
and configuring Remote Bridging for PPP links.
Table of Contents
1. Historical Perspective ................................ 2
2. Methods of Bridging ................................... 3
2.1 Transparent Bridging ............................ 3
2.2 Remote Transparent Bridging ..................... 3
2.3 Source Routing .................................. 4
2.4 Remote Source Route Bridging .................... 5
2.5 SR-TB Translational Bridging .................... 6
3. Traffic Services ...................................... 6
3.1 LAN Frame Checksum Preservation ................. 6
3.2 Traffic having no LAN Frame Checksum ............ 6
3.3 Tinygram Compression ............................ 7
3.4 LAN Identification .............................. 7
4. A PPP Network Control Protocol for Bridging ........... 9
4.1 Sending Bridge Frames ........................... 10
4.1.1 Maximum Receive Unit Considerations ............. 10
4.1.2 Loopback and Link Quality Monitoring ............ 11
4.1.3 Message Sequence ................................ 11
4.1.4 Separation of Spanning Tree Domains ............. 11
4.2 Bridged LAN Traffic ............................. 12
4.3 Spanning Tree Bridge PDU ........................ 16
5. BCP Configuration Options ............................. 17
5.1 Bridge-Identification ........................... 17
5.2 Line-Identification ............................. 19
5.3 MAC-Support ..................................... 20
5.4 Tinygram-Compression ............................ 21
5.5 LAN-Identification .............................. 22
5.6 MAC-Address ..................................... 23
5.7 Spanning-Tree-Protocol .......................... 24
APPENDICES ................................................ 26
A. Tinygram-Compression Pseudo-Code ................... 26
SECURITY CONSIDERATIONS ................................... 27
REFERENCES ................................................ 27
ACKNOWLEDGEMENTS ............................................. 28
CHAIR'S ADDRESS .............................................. 28
AUTHOR'S ADDRESS ............................................. 28
1. Historical Perspective
Two basic algorithms are ambient in the industry for Bridging of
Local Area Networks. The more common algorithm is called
"Transparent Bridging", and has been standardized for Extended LAN
configurations by IEEE 802.1. The other is called "Source Route
Bridging", and is prevalent on IEEE 802.5 Token Ring LANs.
The IEEE has combined these two methods into a device called a Source
Routing Transparent (SRT) bridge, which concurrently provides both
Source Route and Transparent bridging. Transparent and SRT bridges
are specified in IEEE standard 802.1D [3].
Although IEEE committee 802.1G is addressing remote bridging [2],
neither standard directly defines the mechanisms for implementing
remote bridging. Technically, that would be beyond the IEEE 802
committee's charter. However, both 802.1D and 802.1G allow for it.
The implementor may model the line either as a component within a
single MAC Relay Entity, or as the LAN media between two remote
bridges.
2. Methods of Bridging
2.1. Transparent Bridging
As a favor to the uninitiated, let us first describe Transparent
Bridging. Essentially, the bridges in a network operate as isolated
entities, largely unaware of each others' presence. A Transparent
Bridge maintains a Forwarding Database consisting of
{address, interface}
records, by saving the Source Address of each LAN transmission that
it receives, along with the interface identifier for the interface it
was received on. It goes on to check whether the Destination Address
is in the database, and if so, either discards the message when the
destination and source are located at the same interface, or forwards
the message to the indicated interface. A message whose Destination
Address is not found in the table is forwarded to all interfaces
except the one it was received on. This behavior applies to
Broadcast/Multicast frames as well.
The obvious fly in the ointment is that redundant paths in the
network cause indeterminate (nay, all too determinate) forwarding
behavior to occur. To prevent this, a protocol called the Spanning
Tree Protocol is executed between the bridges to detect and logically
remove redundant paths from the network.
One system is elected as the "Root", which periodically emits a
message called a Bridge Protocol Data Unit (BPDU), heard by all of
its neighboring bridges. Each of these modifies and passes the BPDU
on to its neighbors, until it arrives at the leaf LAN segments in the
network (where it dies, having no further neighbors to pass it
along), or until the message is stopped by a bridge which has a
superior path to the "Root". In this latter case, the interface the
BPDU was received on is ignored (it is placed in a Hot Standby
status, no traffic is emitted onto it except the BPDU, and all
traffic received from it is discarded), until a topology change
forces a recalculation of the network.
2.2. Remote Transparent Bridging
There exist two basic sorts of bridges -- those that interconnect
LANs directly, called Local Bridges, and those that interconnect LANs
via an intermediate medium sUCh as a leased line, called Remote
Bridges. PPP may be used to connect Remote Bridges.
The IEEE 802.1G Remote MAC Bridging committee has proposed a model of
a Remote Bridge in which a set of two or more Remote Bridges that are
interconnected via remote lines are termed a Remote Bridge Group.
Within a Group, a Remote Bridge Cluster is dynamically formed through
execution of the spanning tree as the set of bridges that may pass
frames among each other.
This model bestows on the remote lines the basic properties of a LAN,
but does not require a one-to-one mapping of lines to virtual LAN
segments. For instance, the model of three interconnected Remote
Bridges, A, B and C, may be that of a virtual LAN segment between A
and B and another between B and C. However, if a line exists between
Remote Bridges B and C, a frame could actually be sent directly from
B to C, as long as there was the external appearance that it had
travelled through A.
IEEE 802.1G thus allows for a great deal of implementation freedom
for features such as route optimization and load balancing, as long
as the model is maintained.
For simplicity and because the 802.1G proposal has not been approved
as a standard, we discuss Remote Bridging in this document in terms
of two Remote Bridges connected by a single line. Within the 802.1G
framework, these two bridges would comprise a Remote Bridge Group.
This convention is not intended to preclude the use of PPP bridging
in larger Groups, as allowed by 802.1G.
2.3. Source Routing
The IEEE 802.1D Committee has standardized Source Routing for any MAC
Type that allows its use. Currently, MAC Types that support Source
Routing are FDDI and IEEE 802.5 Token Ring.
The IEEE standard defines Source Routing only as a component of an
SRT bridge. However, many bridges have been implemented which are
capable of performing Source Routing alone. These are most commonly
implemented in accordance either with the IBM Token-Ring Network
Architecture Reference [1] or with the Source Routing Appendix of
IEEE 802.1D [3].
In the Source Routing approach, the originating system has the
responsibility of indicating the path that the message should follow.
It does this, if the message is directed off of the local segment, by
including a variable length MAC header extension called the Routing
Information Field (RIF). The RIF consists of one 16-bit Word of
flags and parameters, followed by zero or more segment-and-bridge
identifiers. Each bridge en route determines from this source route
list whether it should accept the message and how to forward it.
In order to discover the path to a destination, the originating
system transmits an EXPlorer frame. An All-Routes Explorer (ARE)
frame follows all possible paths to a destination. A Spanning Tree
Explorer (STE) frame follows only those paths defined by Bridge ports
that the Spanning Tree Algorithm has put in Forwarding state. Port
states do not apply to ARE or Specifically-Routed Frames. The
destination system replies to each copy of an ARE frame with a
Specifically-Routed Frame, and to an STE frame with an ARE frame. In
either case, the originating station may receive multiple replies,
from which it chooses the route it will use for future Specifically-
Routed Frames.
The algorithm for Source Routing requires the bridge to be able to
identify any interface by its segment-and-bridge identifier. When a
packet is received that has the RIF present, a boolean in the RIF is
inspected to determine whether the segment-and-bridge identifiers are
to be inspected in "forward" or "reverse" sense. In its search, the
bridge looks for the segment-and-bridge identifier of the interface
the packet was received on, and forwards the packet toward the
segment identified in the segment-and-bridge identifier that follows
it.
2.4. Remote Source Route Bridging
There is no Remote Source Route Bridge proposal in IEEE 802.1 at this
time, although many vendors ship remote Source Routing Bridges.
We allow for modelling the line either as a connection residing
between two halves of a "split" Bridge (the split-bridge model), or
as a LAN segment between two Bridges (the independent-bridge model).
In the latter case, the line requires a LAN Segment ID.
By default, PPP Source Route Bridges use the independent-bridge
model. This requirement ensures interoperability in the absence of
option negotiation. In order to use the split-bridge model, a system
MUST successfully negotiate the Bridge-Identification Configuration
Option.
Although no option negotiation is required for a system to use the
independent-bridge model, it is strongly recommended that systems
using this model negotiate the Line-Identification Configuration
Option. Doing so will verify correct configuration of the LAN
Segment Id assigned to the line.
When two PPP systems use the split-bridge model, the system that
transmits an Explorer frame onto the PPP link MUST update the RIF on
behalf of the two systems. The purpose of this constraint is to
ensure interoperability and to preserve the simplicity of the
bridging algorithm. For example, if the receiving system did not
know whether the transmitting system had updated the RIF, it would
have to scan the RIF and decide whether to update it. The choice of
the transmitting system for the role of updating the RIF allows the
system receiving the frame from the PPP link to forward the frame
without processing the RIF.
Given that source routing is configured on a line or set of lines,
the specifics of the link state with respect to STE frames are
defined by the Spanning Tree Protocol in use. Choice of the split-
bridge or independent-bridge model does not affect spanning tree
operation. In both cases, the spanning tree protocol is executed on
the two systems independently.
2.5. SR-TB Translational Bridging
IEEE 802 is not currently addressing bridges that translate between
Transparent Bridging and Source Routing. For the purposes of this
standard, such a device is either a Transparent or a Source Routing
bridge, and will act on the line in one of these two ways, just as it
does on the LAN.
3. Traffic Services
Several services are provided for the benefit of different system
types and user configurations. These include LAN Frame Checksum
Preservation, LAN Frame Checksum Generation, Tinygram Compression,
and the identification of closed sets of LANs.
3.1. LAN Frame Checksum Preservation
IEEE 802.1 stipulates that the Extended LAN must enjoy the same
probability of undetected error that an individual LAN enjoys.
Although there has been considerable debate concerning the algorithm,
no other algorithm has been proposed than having the LAN Frame
Checksum received by the ultimate receiver be the same value
calculated by the original transmitter. Achieving this requires, of
course, that the line protocols preserve the LAN Frame Checksum from
end to end. The protocol is optimized towards this approach.
3.2. Traffic having no LAN Frame Checksum
The fact that the protocol is optimized towards LAN Frame Checksum
preservation raises twin questions: "What is the approach to be used
by systems which, for whatever reason, cannot easily support Frame
Checksum preservation?" and "What is the approach to be used when the
system originates a message, which therefore has no Frame Checksum
precalculated?".
Surely, one approach would be to require stations to calculate the
Frame Checksum in software if hardware support were unavailable; this
would meet with profound dismay, and would raise serious questions of
interpretation in a Bridge/Router.
However, stations which implement LAN Frame Checksum preservation
must already solve this problem, as they do originate traffic.
Therefore, the solution adopted is that messages which have no Frame
Checksum are tagged and carried across the line.
When a system which does not implement LAN Frame Checksum
preservation receives a frame having an embedded FCS, it converts it
for its own use by removing the trailing four octets. When any
system forwards a frame which contains no embedded FCS to a LAN, it
forwards it in a way which causes the FCS to be calculated.
3.3. Tinygram Compression
An issue in remote Ethernet bridging is that the protocols that are
most attractive to bridge are prone to problems on low speed (64 KBPS
and below) lines. This can be partially alleviated by observing that
the vendors defining these protocols often fill the PDU with octets
of ZERO. Thus, an Ethernet or IEEE 802.3 PDU received from a line
that is (1) smaller than the minimum PDU size, and (2) has a LAN
Frame Checksum present, must be padded by inserting zeroes between
the last four octets and the rest of the PDU before transmitting it
on a LAN. These protocols are frequently used for interactive
sessions, and therefore are frequently this small.
To prevent ambiguity, PDUs requiring padding are explicitly tagged.
Compression is at the option of the transmitting station, and is
probably performed only on low speed lines, perhaps under
configuration control.
The pseudo-code in Appendix 1 describes the algorithms.
3.4. LAN Identification
In some applications, it is useful to tag traffic by the user
community it is a part of, and guarantee that it will be only emitted
onto a LAN which is of the same community. The user community is
defined by a LAN ID. Systems which choose to not implement this
feature must assume that any frame received having a LAN ID is from a
different community than theirs, and discard it.
It should be noted that the enabling of the LAN Identification option
requires behavior consistent with the following additions to the
standard bridging algorithm.
Each bridge port may be considered to have two additional variables
associated with it: "domain" and "checkDomain".
The variable "domain" (a 32-bit unsigned integer) is assigned a value
that uniquely labels a set of bridge ports in an extended network,
with a default value of 1, and the values of 0 and 0xffffffff being
reserved.
The variable "checkDomain" (a boolean) controls whether this value is
used to filter output to a bridge port. The variable "checkDomain"
is generally set to the boolean value True for LAN bridge ports, and
set to the boolean value False for WAN bridge ports.
The action of the bridge is then as modified as expressed in the
following C code fragments:
On a packet being received from a bridge port:
if (domainNotPresentWithPacket) {
packetInformation.domain = portInformation[inputPort].domain;
} else {
packetInformation.domain = domainPresentWithPacket;
}
On a packet being transmitted from a bridge port:
if (portInformation[outputPort].checkDomain &&
portInformation[outputPort] != packetInformation.domain) {
discardPacket();
return;
}
For example, suppose you have the following configuration:
E1 +--+ +--+ E3
------------ ------------
W1
B1------------B2
E2 E4
------------ ------------
+--+ +--+
E1, E2, E3, and E4 are Ethernet LANs (or Token Ring, FDDI, etc.). W1
is a WAN (PPP over T1). B1 and B2 are MAC level bridges.
You want End Stations on E1 and E3 to communicate, and you want End
Stations on E2 and E4 to communicate, but you do not want End
Stations on E1 and E3 to communicate with End Stations on E2 and E4.
This is true for Unicast, Multicast, and Broadcast traffic. If a
broadcast datagram originates on E1, you want it only to be
propagated to E3, and not on E2 or E4.
Another way of looking at it is that E1 and E3 form a Virtual LAN,
and E2 and E4 form a Virtual LAN, as if the following configuration
were actually being used:
E1 +--+ W2 +--+ E3
------------B3------------B4------------
+--+ +--+
E2 +--+ W3 +--+ E4
------------B5------------B6------------
+--+ +--+
To accomplish this (using the LAN Identification option), B1 and B2
negotiate this option on, and send datagrams with bit 6 set to 1,
with the LAN ID field inserted in the frame. Traffic on E1 and E3
would be assigned LAN ID 1, and traffic on E2 and E4 would be
assigned LAN ID 2. Thus B1 and B2 can separate traffic going over
W1.
Note that execution of the spanning tree algorithm may result in the
subdivision of a domain. The administrator of LAN domains must
ensure, through spanning tree configuration and topology design, that
such subdivision does not occur.
4. A PPP Network Control Protocol for Bridging
The Bridging Control Protocol (BCP) is responsible for configuring,
enabling and disabling the bridge protocol modules on both ends of
the point-to-point link. BCP uses the same packet exchange mechanism
as the Link Control Protocol. BCP packets may not be exchanged until
PPP has reached the Network-Layer Protocol phase. BCP packets
received before this phase is reached SHOULD be silently discarded.
The Bridging Control Protocol is exactly the same as the Link Control
Protocol [6] with the following exceptions:
Frame Modifications
The packet may utilize any modifications to the basic frame format
which have been negotiated during the Link Establishment phase.
Implementations SHOULD NOT negotiate Address-and-Control-Field-
Compression or Protocol-Field-Compression on other than low speed
links.
Data Link Layer Protocol Field
Exactly one BCP packet is encapsulated in the PPP Information
field, where the PPP Protocol field indicates type hex 8031 (BCP).
Code field
Only Codes 1 through 7 (Configure-Request, Configure-Ack,
Configure-Nak, Configure-Reject, Terminate-Request, Terminate-Ack
and Code-Reject) are used. Other Codes SHOULD be treated as
unrecognized and SHOULD result in Code-Rejects.
Timeouts
BCP packets may not be exchanged until PPP has reached the
Network-Layer Protocol phase. An implementation SHOULD be
prepared to wait for Authentication and Link Quality Determination
to finish before timing out waiting for a Configure-Ack or other
response. It is suggested that an implementation give up only
after user intervention or a configurable amount of time.
Configuration Option Types
BCP has a distinct set of Configuration Options, which are defined
in this document.
4.1. Sending Bridge Frames
Before any Bridged LAN Traffic or BPDUs may be communicated, PPP MUST
reach the Network-Layer Protocol phase, and the Bridging Control
Protocol MUST reach the Opened state.
Exactly one Bridged LAN Traffic or BPDU is encapsulated in the PPP
Information field, where the PPP Protocol field indicates type hex
0031 (Bridged PDU).
4.1.1. Maximum Receive Unit Considerations
The maximum length of a Bridged datagram transmitted over a PPP link
is the same as the maximum length of the Information field of a PPP
encapsulated packet. Since there is no standard method for
fragmenting and reassembling Bridged PDUs, PPP links supporting
Bridging MUST negotiate an MRU large enough to support the MAC Types
that are later negotiated for Bridging support. Because they include
the MAC headers, even bridged Ethernet frames are larger than the
default PPP MRU of 1500 octets.
4.1.2. Loopback and Link Quality Monitoring
It is strongly recommended that PPP Bridge Protocol implementations
utilize Magic Number Loopback Detection and Link-Quality-Monitoring.
The 802.1 Spanning Tree protocol, which is integral to both
Transparent Bridging and Source Routing (as standardized), is
unidirectional during normal operation. Configuration BPDUs emanate
from the Root system in the general direction of the leaves, without
any reverse traffic except in response to network events.
4.1.3. Message Sequence
The multiple link case requires consideration of message
sequentiality. The transmitting system may determine either that the
protocol being bridged requires transmissions to arrive in the order
of their original transmission, and enqueue all transmissions on a
given conversation onto the same link to force order preservation, or
that the protocol does NOT require transmissions to arrive in the
order of their original transmission, and use that knowledge to
optimize the utilization of several links, enqueuing traffic to
multiple links to minimize delay.
In the absence of such a determination, the transmitting system MUST
act as though all protocols require order preservation. Many
protocols designed primarily for use on a single LAN require order
preservation.
Work is currently in progress on a protocol to allow use of multiple
PPP links [7]. If approved, this protocol will allow use of multiple
links while maintaining message sequentiality for Bridged LAN Traffic
and BPDU frames.
4.1.4. Separation of Spanning Tree Domains
It is conceivable that a network manager might wish to inhibit the
exchange of BPDUs on a link in order to logically divide two regions
into separate Spanning Trees with different Roots (and potentially
different Spanning Tree implementations or algorithms). In order to
do that, he should configure both ends to not exchange BPDUs on a
link. An implementation that does not support any spanning tree
protocol MUST silently discard any received IEEE 802.1D BPDU packets,
and MUST either silently discard or respond to other received BPDU
packets with an LCP Protocol-Reject packet.
4.2. Bridged LAN Traffic
For Bridging LAN traffic, the format of the frame on the line is
shown below. The fields are transmitted from left to right.
802.3 Frame format
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+
HDLC FLAG
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Address and Control 0x00 0x31
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
FIZ0 Pads MAC Type LAN ID high word (optional)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
LAN ID low word (optional) Destination MAC Address
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Destination MAC Address
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Source MAC Address
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Source MAC Address Length/Type
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
LLC data ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
LAN FCS (optional)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
potential line protocol pad
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Frame FCS HDLC FLAG
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
802.4/802.5/FDDI Frame format
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+
HDLC FLAG
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Address and Control 0x00 0x31
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
FIZ0 Pads MAC Type LAN ID high word (optional)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
LAN ID low word (optional) Pad Byte Frame Control
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Destination MAC Address
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Destination MAC Address Source MAC Address
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Source MAC Address
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
LLC data ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
LAN FCS (optional)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
optional Data Link Layer padding
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Frame FCS HDLC FLAG
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Address and Control
As defined by the framing in use.
PPP Protocol
0x0031 for PPP Bridging
Flags
bit F: Set if the LAN FCS Field is present
bit I: Set if the LAN ID Field is present
bit Z: Set if IEEE 802.3 Pad must be zero filled to minimum size
bit 0: reserved, must be zero
Pads
Any PPP frame may have padding inserted in the "Optional Data Link
Layer Padding" field. This number tells the receiving system how
many pad octets to strip off.
MAC Type
Up-to-date values of the MAC Type field are specified in the most
recent "Assigned Numbers" RFC[4]. Current values are assigned as
follows:
0: reserved
1: IEEE 802.3/Ethernet with canonical addresses
2: IEEE 802.4 with canonical addresses
3: IEEE 802.5 with non-canonical addresses
4: FDDI with non-canonical addresses
5-10: reserved
11: IEEE 802.5 with canonical addresses
12: FDDI with canonical addresses
"Canonical" is the address format defined as standard address
representation by the IEEE. In this format, the bit within each
byte that is to be transmitted first on a LAN is represented as
the least significant bit. In contrast, in non-canonical form,
the bit within each byte that is to be transmitted first is
represented as the most-significant bit. Many LAN interface
implementations use non-canonical form. In both formats, bytes
are represented in the order of transmission.
If an implementation supports a MAC Type that is the higher-
numbered format of that MAC Type, then it MUST also support the
lower-numbered format of that MAC Type. For example, if an
implementation supports FDDI with canonical address format, then
it MUST also support FDDI with non-canonical address format. The
purpose of this requirement is to provide backward compatibility
with earlier versions of this specification.
A system MUST NOT transmit a MAC Type numbered higher than 4
unless it has received from its peer a MAC-Support Configuration
Option indicating that the peer is willing to receive frames of
that MAC Type.
LAN ID
This optional 32-bit field identifies the Community of LANs which
may be interested to receive this frame. If the LAN ID flag is
not set, then this field is not present, and the PDU is four
octets shorter.
Frame Control
On 802.4, 802.5, and FDDI LANs, there are a few octets preceding
the Destination MAC Address, one of which is protected by the FCS.
The MAC Type of the frame determines the contents of the Frame
Control field. A pad octet is present to provide 32-bit packet
alignment.
Destination MAC Address
As defined by the IEEE. The MAC Type field defines the bit
ordering.
Source MAC Address
As defined by the IEEE. The MAC Type field defines the bit
ordering.
LLC data
This is the remainder of the MAC frame which is (or would be were
it present) protected by the LAN FCS.
For example, the 802.5 Access Control field, and Status Trailer
are not meaningful to transmit to another ring, and are omitted.
LAN FCS
If present, this is the LAN FCS which was calculated by (or which
appears to have been calculated by) the originating station. If
the LAN FCS flag is not set, then this field is not present, and
the PDU is four octets shorter.
Optional Data Link Layer Padding
Any PPP frame may have padding inserted between the Information
field and the Frame FCS. The Pads field contains the length of
this padding, which may not exceed 15 octets.
The PPP LCP Extensions [5] specify a self-describing pad.
Implementations are encouraged to set the Pads field to zero, and
use the self-describing pad instead.
Frame FCS
Mentioned primarily for clarity. The FCS used on the PPP link is
separate from and unrelated to the LAN FCS.
4.3. Spanning Tree Bridge PDU
This is the Spanning Tree BPDU, without any MAC or 802.2 LLC header
(these being functionally equivalent to the Address, Control, and PPP
Protocol Fields). The LAN Pad and Frame Checksum fields are likewise
superfluous and absent.
The Address and Control Fields are subject to LCP Address-and-
Control-Field-Compression negotiation.
A PPP system which is configured to participate in a particular
spanning tree protocol and receives a BPDU of a different spanning
tree protocol SHOULD reject it with the LCP Protocol-Reject. A
system which is configured not to participate in any spanning tree
protocol MUST silently discard all BPDUs.
Spanning Tree Bridge PDU
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+
HDLC FLAG
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Address and Control Spanning Tree Protocol
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
BPDU data ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Frame FCS HDLC FLAG
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Address and Control
As defined by the framing in use.
Spanning Tree Protocol
Up-to-date values of the Spanning-Tree-Protocol field are
specified in the most recent "Assigned Numbers" RFC[4]. Current
values are assigned as follows:
Value (in hex) Protocol
0201 IEEE 802.1 (either 802.1D or 802.1G)
0203 IBM Source Route Bridge
0205 DEC LANbridge 100
The two versions of the IEEE 802.1 spanning tree protocol frames
can be distinguished by fields within the BPDU data.
BPDU data
As defined by the specified Spanning Tree Protocol.
5. BCP Configuration Options
BCP Configuration Options allow modifications to the standard
characteristics of the network-layer protocol to be negotiated. If a
Configuration Option is not included in a Configure-Request packet,
the default value for that Configuration Option is assumed.
BCP uses the same Configuration Option format defined for LCP [6],
with a separate set of Options.
Up-to-date values of the BCP Option Type field are specified in the
most recent "Assigned Numbers" RFC[4]. Current values are assigned
as follows:
1 Bridge-Identification
2 Line-Identification
3 MAC-Support
4 Tinygram-Compression
5 LAN-Identification
6 MAC-Address
7 Spanning-Tree-Protocol
5.1. Bridge-Identification
Description
The Bridge-Identification Configuration Option is designed for use
when the line is an interface between half bridges connecting
virtual or physical LAN segments. Since these remote bridges are
modeled as a single bridge with a strange internal interface, each
remote bridge needs to know the LAN segment and bridge numbers of
the adjacent remote bridge. This option MUST NOT be included in
the same Configure-Request as the Line-Identification option.
The Source Routing Route Descriptor and its use are specified by
the IEEE 802.1D Appendix on Source Routing. It identifies the
segment to which the interface is attached by its configured
segment number, and itself by bridge number on the segment.
The two half bridges MUST agree on the bridge number. If a bridge
number is not agreed upon, the Bridging Control Protocol MUST NOT
enter the Opened state.
Since mismatched bridge numbers are indicative of a configuration
error, it is strongly recommended that a system not change its
bridge number for the purpose of resolving a mismatch. However,
to allow two systems to proceed to the Opened state despite a
mismatch, a system MAY change its bridge number to the higher of
the two numbers. A higher-numbered system MUST NOT change its
bridge number to a lower number.
By default, a system that does not negotiate this option is
assumed to be configured not to use the model of the two systems
as two halves of a single source-route bridge. It is instead
assumed to be configured to use the model of the two systems as
two independent bridges.
Example
If System A announces LAN Segment AAA, Bridge #1, and System B
announces LAN Segment BBB, Bridge #1, then the resulting Source
Routing configuration (read in the appropriate direction) is then
AAA,1,BBB.
A summary of the Bridge-Identification Option format is shown below.
The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type Length LAN Segment Number Bridge#
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
1
Length
4
LAN Segment Number
A 12-bit number identifying the LAN segment, as defined in the
IEEE 802.1D Source Routing Specification.
Bridge Number
A 4-bit number identifying the bridge on the LAN segment, as
defined in the IEEE 802.1D Source Routing Specification.
5.2. Line-Identification
Description
The Line-Identification Configuration Option is designed for use
when the line is assigned a LAN segment number as though it were a
two system LAN segment in accordance with the Source Routing
algorithm. This option MUST NOT be included in the same
Configure-Request as the Bridge-Identification option.
The Source Routing Route Descriptor and its use are specified by
the IEEE 802.1D Appendix on Source Routing. It identifies the
segment to which the interface is attached by its configured
segment number, and itself by bridge number on the segment.
The two bridges MUST agree on the LAN segment number. If a LAN
segment number is not agreed upon, the Bridging Control Protocol
MUST NOT enter the Opened state.
Since mismatched LAN segment numbers are indicative of a
configuration error, it is strongly recommended that a system not
change its LAN segment number for the purpose of resolving a
mismatch. However, to allow two systems to proceed to the Opened
state despite a mismatch, a system MAY change its LAN segment
number to the higher of the two numbers. A higher-numbered system
MUST NOT change its LAN segment number to a lower number.
By default, a system that does not negotiate this option is
assumed to have its LAN segment number correctly configured by the
user.
A summary of the Line-Identification Option format is shown below.
The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type Length LAN Segment Number Bridge#
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
2
Length
4
LAN Segment Number
A 12-bit number identifying the LAN segment, as defined in the
IEEE 802.1D Source Routing Specification.
Bridge Number
A 4-bit number identifying the bridge on the LAN segment, as
defined in the IEEE 802.1D Source Routing Specification.
5.3. MAC-Support
Description
The MAC-Support Configuration Option is provided to permit
implementations to indicate the sort of traffic they are prepared
to receive. Negotiation of this option is strongly recommended.
By default, when an implementation does not announce the MAC Types
that it supports, all MAC Types are sent by the peer which are
capable of being transported given other configuration parameters.
The receiver will discard those MAC Types that it does not
support.
A device supporting a 1600 octet MRU might not be willing to
support 802.5, 802.4 or FDDI, which each support frames larger
than 1600 octets.
By announcing the MAC Types it will support, an implementation is
advising its peer that all unspecified MAC Types will be
discarded. The peer MAY then reduce bandwidth usage by not
sending the unsupported MAC Types.
Announcement of support for multiple MAC Types is accomplished by
placing multiple options in the Configure-Request.
The nature of this option is advisory only. This option MUST NOT
be included in a Configure-Nak.
A summary of the MAC-Support Option format is shown below. The
fields are transmitted from left to right.
0 1 2
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type Length MAC Type
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
3
Length
3
MAC Type
One of the values of the PDU MAC Type field (previously described
in the "Bridged LAN Traffic" section) that this system is prepared
to receive and service.
5.4. Tinygram-Compression
Description
This Configuration Option permits the implementation to indicate
support for Tinygram compression.
Not all systems are prepared to make modifications to messages in
transit. On high speed lines, it is probably not worth the
effort.
This option MUST NOT be included in a Configure-Nak if it has been
received in a Configure-Request. This option MAY be included in a
Configure-Nak in order to prompt the peer to send the option in
its next Configure-Request.
By default, no compression is allowed. A system which does not
negotiate, or negotiates this option to be disabled, should never
receive a compressed packet.
A summary of the Tinygram-Compression Option format is shown below.
The fields are transmitted from left to right.
0 1 2
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type Length Enable/Disable
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
4
Length
3
Enable/Disable
If the value is 1, Tinygram-Compression is enabled. If the value
is 2, Tinygram-Compression is disabled, and no decompression will
occur.
The implementations need not agree on the setting of this
parameter. One may be willing to decompress and the other not.
5.5. LAN-Identification
Description
This Configuration Option permits the implementation to indicate
support for the LAN Identification field, and that the system is
prepared to service traffic to any labeled LANs beyond the system.
A Configure-NAK MUST NOT be sent in response to a Configure-
Request that includes this option.
By default, LAN-Identification is disabled. All Bridge LAN
Traffic and BPDUs that contain the LAN ID field will be discarded.
The peer may then reduce bandwidth usage by not sending the
unsupported traffic.
A summary of the LAN-Identification Option format is shown below.
The fields are transmitted from left to right.
0 1 2
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type Length Enable/Disable
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
5
Length
3
Enable/Disable
If the value is 1, LAN Identification is enabled. If the value is
2, LAN Identification is disabled.
The implementations need not agree on the setting of this
parameter. One may be willing to accept LAN Identification and
the other not.
5.6. MAC-Address
Description
The MAC-Address Configuration Option enables the implementation to
announce its MAC address or have one assigned. The MAC address is
represented in IEEE 802.1 Canonical format, which is to say that
the multicast bit is the least significant bit of the first octet
of the address.
If the system wishes to announce its MAC address, it sends the
option with its MAC address specified. When specifying a non-zero
MAC address in a Configure-Request, any inclusion of this option
in a Configure-Nak MUST be ignored.
If the implementation wishes to have a MAC address assigned, it
sends the option with a MAC address of 00-00-00-00-00-00. Systems
that have no mechanism for address assignment will Configure-
Reject the option.
A Configure-Nak MUST specify a valid IEEE 802.1 format physical
address; the multicast bit MUST be zero. It is strongly
recommended (although not mandatory) that the "locally assigned
address" bit (the second least significant bit in the first octet)
be set, indicating a locally assigned address.
A summary of the MAC-Address Option format is shown below. The
fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type Length MAC byte 1 LM MAC byte 2
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
MAC byte 3 MAC byte 4 MAC byte 5 MAC byte 6
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
6
Length
8
MAC Byte
Six octets of MAC address in 802.1 Canonical order. For clarity,
the position of the Local Assignment (L) and Multicast (M) bits
are shown in the diagram.
5.7. Spanning-Tree-Protocol
Description
The Spanning-Tree-Protocol Configuration Option enables the
Bridges to negotiate the version of the spanning tree protocol in
which they will participate.
If both bridges support a spanning tree protocol, they MUST agree
on the protocol to be supported. When the two disagree, the
lower-numbered of the two spanning tree protocols should be used.
To resolve the conflict, the system with the lower-numbered
protocol SHOULD Configure-Nak the option, suggesting its own
protocol for use. If a spanning tree protocol is not agreed upon,
except for the case in which one system does not support any
spanning tree protocol, the Bridging Control Protocol MUST NOT
enter the Opened state.
Most systems will only participate in a single spanning tree
protocol. If a system wishes to participate simultaneously in
more than one spanning tree protocol, it MAY include all of the
appropriate protocol types in a single Spanning-Tree-Protocol
Configuration Option. The protocol types MUST be specified in
increasing numerical order. For the purpose of comparison during
negotiation, the protocol numbers MUST be considered to be a
single number. For instance, if System A includes protocols 01
and 03 and System B indicates protocol 03, System B should
Configure-Nak and indicate a protocol type of 03 since 0103 is
greater than 03.
By default, an implementation MUST either support the IEEE 802.1D
spanning tree or support no spanning tree protocol. An
implementation that does not support any spanning tree protocol
MUST silently discard any received IEEE 802.1D BPDU packets, and
MUST either silently discard or respond to other received BPDU
packets with an LCP Protocol-Reject packet.
A summary of the Spanning-Tree-Protocol Option format is shown below.
The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type Length Protocol 1 Protocol 2 ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
7
Length
2 octets plus 1 additional octet for each protocol that will be
actively supported. Most systems will only support a single
spanning tree protocol, resulting in a length of 3.
Protocol n
Each Protocol field is one octet and indicates a desired spanning
tree protocol. Up-to-date values of the Protocol field are
specified in the most recent "Assigned Numbers" RFC[4]. Current
values are assigned as follows:
Value Protocol
0 Null (no Spanning Tree protocol supported)
1 IEEE 802.1D spanning tree
2 IEEE 802.1G extended spanning tree protocol
3 IBM Source Route Spanning tree protocol
4 DEC LANbridge 100 Spanning tree protocol
A. Tinygram-Compression Pseudo-Code
PPP Transmitter:
if (ZeroPadCompressionEnabled &&
BridgedProtocolHeaderFormat == IEEE8023 &&
PacketLength == Minimum8023PacketLength) {
/*
* Remove any continuous run of zero octets preceding,
* but not including, the LAN FCS, but not extending
* into the MAC header.
*/
Set (ZeroCompressionFlag); /* Signal receiver */
if (is_Set (LAN_FCS_Present)) {
FCS = TrailingOctets (PDU, 4); /* Store FCS */
RemoveTrailingOctets (PDU, 4); /* Remove FCS */
while (PacketLength > 14 && /* Stop at MAC header or */
TrailingOctet (PDU) == 0) /* last non-zero octet */
RemoveTrailingOctets (PDU, 1);/* Remove zero octet */
Appendbuf (PDU, 4, FCS); /* Restore FCS */
}
else {
while (PacketLength > 14 && /* Stop at MAC header */
TrailingOctet (PDU) == 0) /* or last zero octet */
RemoveTrailingOctets (PDU, 1);/* Remove zero octet */
}
}
PPP Receiver:
if (ZeroCompressionFlag) { /* Flag set in header? */
/* Restoring packet to minimum 802.3 length */
Clear (ZeroCompressionFlag);
if (is_Set (LAN_FCS_Present)) {
FCS = TrailingOctets (PDU, 4); /* Store FCS */
RemoveTrailingOctets (PDU, 4); /* Remove FCS */
Appendbuf (PDU, 60 - PacketLength, zeroes);/* Add zeroes */
Appendbuf (PDU, 4, FCS); /* Restore FCS */
}
else {
Appendbuf (PDU, 60 - PacketLength, zeroes);/* Add zeroes */
}
}
Security Considerations
Security issues are not discussed in this memo.
References
[1] IBM, "Token-Ring Network Architecture Reference", 3rd edition,
September 1989.
[2] IEEE 802.1, "Draft Standard 802.1G: Remote MAC Bridging",
P802.1G/D7, December 30, 1992.
[3] IEEE 802.1, "Media Access Control (MAC) Bridges", ISO/IEC 15802-
3:1993 ANSI/IEEE Std 802.1D, 1993 edition., July 1993.
[4] Reynolds, J., and J. Postel, "Assigned Numbers", STD 2, RFC1340,
USC/Information Sciences Institute, July 1992.
[5] Simpson, W., "PPP LCP Extensions", RFC1570, Daydreamer, January
1994.
[6] Simpson, W., "The Point-to-Point Protocol (PPP)", RFC1548,
Daydreamer, December 1993.
[7] Sklower, K., "A Multilink Protocol for Synchronizing the
Transmission of Multi-protocol Datagrams", Work in Progress,
August 1993.
Acknowledgments
This document is a product of the Point-to-Point Protocol Extensions
Working Group.
Special thanks go to Steve Senum of Network Systems, Dino Farinacci
of 3COM, Rick Szmauz of Digital Equipment Corporation, and Andrew
Fuqua of IBM.
Chair's Address
The working group can be contacted via the current chair:
Fred Baker
Advanced Computer Communications
315 Bollay Drive
Santa Barbara, California 93117
EMail: fbaker@acc.com
Author's Address
Questions about this memo can also be directed to:
Rich Bowen
International Business Machines Corporation
P. O. Box 12195
Research Triangle Park, NC 27709
Phone: (919) 543-9851
